manualshive.com logo in svg

Canon CLBP-460PS, Service Manual

Share
Download
Canon CLBP-460PS Service Manual Download Page 16

PostScript fonts: 136 (117 Adobe Type 1 fonts, 19 Truetype fonts)

1 - 6

CHAPTER 1

Type face

• Adobe Type 1 PostScript fonts
AlbertusMT, AlbertusMT-Italic, AlbertusMT-Light,
AntiqueOlive-Roman, AntiqueOlive-Bold, AntiqueOlive-
Compact, AntiqueOlive-Italic, AvantGarde-Book,
AvantGarde-BookOblique, AvantGarde-Demi, AvantGarde-
DemiOblique, Bodoni, Bodoni-Bold, Bodoni-Italic, Bodoni-
BoldItalic, Bodoni-Poster, Bodoni-PosterCompressed,
Bookman-Demi, Bookman-DemiItalic, Bookman-Light,
Bookman-LightItalic, Carta, Clarendon, Clarendon-Bold,
Clarendon-Light, CooperBlack, CooperBlack-Italic,
Copperplate-ThirtyThreeBC, Copperplate-ThirtyTwoBC,
Coronet, Courier, Courier-Bold, Courier-Oblique, Courier-
BoldOblique, Eurostile, Eurostile-Bold, Eurostile-
ExtendedTow, Eurostile-BoldExtendedTow, GillSans,
GillSans-Bold, GillSans-Italic, GillSans-BoldItalic, GillSans-
Condensed, GillSans-BoldCondensed, GillSans-Light,
GillSans-LightItalic, GillSans-ExtraBold, Goudy, Goudy-
Bold, Goudy-Italic, Goudy-BoldItalic, Goudy-ExtraBold,
Helvetica, Helvetica-Bold, Helvetica-BoldOblique, Helvetica-
Condensed, Helvetica-Condensed-Bold, Helvetica-
Condensed-BoldObl, Helvetica-Condensed-Oblique,
Helvetica-Narrow, Helvetica-Narrow-Bold, Helvetica-Narrow-
BoldOblique, Helvetica-Narrow-Oblique, Helvetica-Oblique,
JoannaMT, JoannaMT-Bold, JoannaMT-Italic, JoannaMT-
BoldItalic, LetterGothic, LetterGothic-Bold, LetterGothic-
BoldSlanted, LetterGothic-Slanted, LubalinGraph-Book,
LubalinGraph-BookOblique, LubalinGraph-Demi,
LubalinGraph-DemiOblique, Marigold, MonaLisa-Recut,
NewCenturySchlbk-Roman, NewCenturySchlbk-Bold,
NewCenturySchlbk-Italic, NewCenturySchlbk-BoldItalic,
Optima, Optima-Bold, Optima-Italic, Optima-BoldItalic,
Oxford, Palatino-Roman, Palatino-Bold,
Palatino-Italic, Palatino-BoldItalic, StempelGaramond-
Roman, StempelGaramond-Bold, StempelGaramond-Italic,
StempelGaramond-BoldItalic, Symbol, Tekton, Times-
Roman, Times-Bold, Times-Italic, Times-BoldItalic, Univers,
Univers-Bold, Univers-BoldExt, Univers-BoldExtObl,
Univers-BoldOblique, Univers-Condensed, Univers-
CondensedBold, Univers-CondensedBoldOblique, Univers-
CondensedOblique, Univers-Extended, Univers-
ExtendedObl, Univers-Lighit, Univers-LighitOblique,
Univers-Oblique, ZapfChancery-MediumItalic,
ZapfDingbats.

• TrueType fonts
Apple-Chancery, ArialMT, Arial-BoldMT, Arial-ItalicMT,
Arial-BoldItalicMT, Chicago, Geneva, HoeflerText-Regular,
HoeflerText-Black, HoeflerText-Italic, HoeflerText-
BlackItalic, HoeflerText-Ornaments, Monaco, NewYork,
TimesNweRomanPSMT, TimesNweRomanPS-BoldMT,
TimesNweRomanPS-ItalicMT, TimesNweRomanPS-
BoldItalicMT, Wingdings-Regular.  

Scalable

Pitch
(CPI)

Size
(Points)

Remarks

It is possible to
print both portrait
and landscape ori-
entations.

Summary of Contents for CLBP-460PS























































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands