manualshive.com logo in svg

Brother PR1055X, Operation Manual

Looking for an Operation Manual for the Brother PR1055X? Look no further! Download the free manual from our website and unlock the full potential of this remarkable embroidery machine. Our user-friendly platform ensures hassle-free access to this essential resource - visit manualshive.com today!

Share
Download
background image

APPENDIX

181

5

The upper thread breaks.

The needle is not correctly installed.

176

The needle set screw is loose.

176

The needle is bent or blunt.

176

The area around the hole in the needle plate is 
damaged.

1

Scratches/Burrs

• Replace the needle plate.

*

The needle is touching the needle plate.

1

Needle

2

Needle plate hole

3

Needle touching hole

*

The presser foot is set too high and not correctly 
positioned.
The needle hits/touches the presser foot.

*

The area around the embroidery foot hole is 
damaged.

1

Scratches/Burrs

• Replace the presser foot.

*

Using a specialty thread like a metallic thread.
• Slow down the machine embroidery speed.

89

Symptom

Probable Cause/Remedy

Page

Sliding surface on hook is not smooth. There are 
burns on it.

1

Hook race area

*

The thread is loose in the hook area.

173

The play between the hook and the race is too 
much.

*

The hook does not rotate smoothly.
• Remove lint, clean and apply oil.

173, 178

The space between the hook stopper and the 
hook cannot be adjusted.

*

The upper thread is not threaded correctly.

• Pull the upper thread by hand from below the 

presser foot, and check that the thread moves 
smoothly. If the thread does not move 
smoothly, it is not correctly threaded. Un-
thread the machine and re-thread the machine. 
Make sure the thread is correctly positioned in 
the needle bar thread guide.

82

Upper thread is not positioned in upper or middle 
thread guide.
• Make sure thread passes completely under 

upper and middle thread guide.

82

There are knots or tangles in the thread.
• Remove any knots or tangles.

—

The upper thread tension is too high.

118

The bobbin thread tension is incorrect.
The thread does not roll out of the bobbin case 
smoothly.

116

The bobbin case is damaged.
• Replace the bobbin case with a new one.

33

The bobbin thread is not wound correctly.
• Check that the bobbin is wound so that it is 

about 80% full and that the thread is evenly 
wound. If the bobbin is not correctly wound, 
replace the bobbin with one that is correctly 
wound or rewind the bobbin.

33

Symptom

Probable Cause/Remedy

Page

Summary of Contents for PR1055X









































































































































































































Reviews:

No comments

Related manuals for PR1055X

Baby Lock Ellageo PLUS BLL2 Quick Reference Manual preview
Ellageo PLUS BLL2
Brand: Baby Lock Pages: 43
Baby Lock Diana BL480A Instruction And Reference Manual preview
Diana BL480A
Brand: Baby Lock Pages: 71
Baby Lock BL50A Getting To Know preview
BL50A
Brand: Baby Lock Pages: 2
Baby Lock BL50A Quick Reference Manual preview
BL50A
Brand: Baby Lock Pages: 2
Baby Lock A_LINE Maria BL23A Instruction And Reference Manual preview
A_LINE Maria BL23A
Brand: Baby Lock Pages: 78
Baby Lock A-LINE Natalie BL18A Instruction And Reference Manual preview
A-LINE Natalie BL18A
Brand: Baby Lock Pages: 70
Baby Lock A-LINE Lauren BL450A Getting To Know Manual preview
A-LINE Lauren BL450A
Brand: Baby Lock Pages: 12
Baby Lock Aventura BLMAV Instruction And Reference Manual preview
Aventura BLMAV
Brand: Baby Lock Pages: 204
Baby Lock Aventura BLMAV Quick Reference Manual preview
Aventura BLMAV
Brand: Baby Lock Pages: 24
Baby Lock Elissimo & Elissimo GOLD BLSO-BF2 Quick Reference Manual preview
Elissimo & Elissimo GOLD BLSO-BF2
Brand: Baby Lock Pages: 22
Baby Lock BLRG20ST Instruction And Reference Manual preview
BLRG20ST
Brand: Baby Lock Pages: 64
Pfaff 3704-2/02 Instruction Manual preview
3704-2/02
Brand: Pfaff Pages: 122
Cyklos CFM 600 Operating Manual preview
CFM 600
Brand: Cyklos Pages: 7
Stihl RE 98 Instruction Manual preview
RE 98
Brand: Stihl Pages: 132
JUKI MO-70BA Instruction Manual preview
MO-70BA
Brand: JUKI Pages: 247
NexxTech 4313385 Owner'S Manual preview
4313385
Brand: NexxTech Pages: 5
MULTIQUIP Mikasa MVH-200DA Operations & Parts Manual preview
Mikasa MVH-200DA
Brand: MULTIQUIP Pages: 64
JUKI MCS-1500 Instruction Manual preview
MCS-1500
Brand: JUKI Pages: 40

Brands by name

Popular brands

Load more brands