Brother PR1055X Operation Manual Download Page 148

Page: 148 / 200

146

Press the main power switch to start winding the
bobbin.



Start winding the bobbin.

The bobbin will stop rotating automatically when it is
done winding, and the bobbin holder will return to its
original position.

Remove the bobbin.

Pull the thread through the guide slit in the bobbin
winder seat to cut the thread with the cutter.

■

If bobbin winding is stopped before it is
finished

The bobbin winder stops automatically if the thread does
not feed, for example, if it becomes tangled on the spool
pin. If this occurs, correctly thread the bobbin winder, and
then wind the bobbin correctly.

Note

• When removing the bobbin, do not pull on the

bobbin winder seat. Doing so could loosen or
remove the bobbin winder seat, resulting in
damage to the bobbin winder.

CAUTION

• Check that the bobbin thread has been wound

correctly, otherwise the needle may break or
the thread tension will be incorrect.

• Be sure to clean the bobbin case each time

that the bobbin is changed. For details, refer to
“Cleaning the bobbin case” on page 175.

• Be sure to check the tension of the bobbin

thread each time that the bobbin is changed.
For detailed instructions on how to adjust the
bobbin tension, refer to page 116.

Summary of Contents for PR1055X









































































































































































































Search results

Summary of Contents for PR1055X

Reviews:

Related manuals for PR1055X

Brands by name

Popular brands

Brother PR1055X, Operation Manual

Search results

Summary of Contents for PR1055X

Reviews:

Related manuals for PR1055X

Brands by name

Popular brands