Brother PR1055X Operation Manual Download Page 170

Page: 170 / 200

168

Touch

, and then select the stitch color.

Touch

after setting the color.

Select the area you want to set stippling effect.

Follow the procedure from step

on page 165 of

“Basic stippling with My Design Center”.

Scanning fabric and stippling

Use the fabric pattern to coordinate with the stippling pattern.

Hoop the fabric in the embroidery frame.

Touch .



The image display screen appears.

Attach the embroidery frame on the machine, and then

touch .



When the message to start scanning appears, touch



Scanning starts.

Touch .

Memo

• Although the instructions in the LCD screen refer to

the scanning frame, this example uses an
embroidery frame for scanning.

Note

• When scanning starts, some of the machine lights

will turn off in certain circumstances, in order to
increase the scan quality. The machine lights will
return to their original brightness when scanning
ends.

• You can import an image of 2 MB or smaller from

USB media or computer.

Summary of Contents for PR1055X









































































































































































































Search results

Summary of Contents for PR1055X

Reviews:

Related manuals for PR1055X

Brands by name

Popular brands

Brother PR1055X, Operation Manual

Search results

Summary of Contents for PR1055X

Reviews:

Related manuals for PR1055X

Brands by name

Popular brands