Brother PR1055X Operation Manual Download Page 138

Page: 138 / 200

136

Select section

to be embroidered, then touch

• Select the sections in alphabetical order.

If necessary, edit the pattern. Then, touch

• For details, refer to “EDITING THE EMBROIDERY

PATTERN” on page 44.

Confirm the pattern size, and then select the
appropriate fabric and the embroidery frame.

• Be sure to select fabric of the size of combined

pattern.

Hoop the appropriate part of the fabric. In this case,
hoop upper-left part of the fabric.

Touch .

Touch

, and then press the “Start/Stop”

button to embroider the pattern section.

When embroidering is finished, the message to confirm

to embroider the next part appears. Touch



A screen appears so that a section of the large-size
embroidery pattern can be selected.

Center of fabric

Memo

• The pattern can be rotated to either the left or right

when

is touched.

Note

• The last step of the stitching of the pattern section

will be an alignment stitching. Use this stitching for
placement of adjacent pattern section.

Summary of Contents for PR1055X









































































































































































































Search results

Summary of Contents for PR1055X

Reviews:

Related manuals for PR1055X

Brands by name

Popular brands

Brother PR1055X, Operation Manual

Search results

Summary of Contents for PR1055X

Reviews:

Related manuals for PR1055X

Brands by name

Popular brands