manualshive.com logo in svg

Brother PR1055X, Operation Manual

Looking for an Operation Manual for the Brother PR1055X? Look no further! Download the free manual from our website and unlock the full potential of this remarkable embroidery machine. Our user-friendly platform ensures hassle-free access to this essential resource - visit manualshive.com today!

Share
Download
background image

180

The needle breaks.

The area around the hole in the needle plate is 
damaged.

1

Scratches/Burrs

• Replace the needle plate.

*

The needle hits/touches the needle plate.

1

Needle

2

Hole in needle plate

3

Needle hits hole

• Replace the needle.

176
*

The presser foot is set too high and not correctly 
positioned.
The needle hits/touches the presser foot.

*

The area around the embroidery foot hole is 
damaged.

1

Scratches or Burrs

• Replace the presser foot.

*

Sliding surface on hook race is not smooth. There 
are scratches or burrs on it.

1

Hook race area

*

The bobbin or bobbin case are not correctly 
installed.

33, 35

The hook is not correctly installed.

*

Symptom

Probable Cause/Remedy

Page

The hook stopper is not correctly installed, the 
hook is making a complete rotation.

*

The upper thread is not threaded correctly.
The upper thread is catching somewhere.

• Pull the upper thread by hand from below the 

presser foot, and check that the thread moves 
smoothly. If the thread does not move, it is not 
threaded correctly. Thread the upper thread 
correctly. Make sure the thread is caught by 
the needle bar thread guide.

82

The upper thread tension is set too high.

118

A bobbin designed specifically for this machine is 
not used.

33

The needle and the hook are not correctly 
passing each other.
• Hook timing may be OFF.

*

There is backlash play (forward/backward) in the 
needle bar case.

*

The thread density of the embroidery data is too 
fine.
Three or more overlapping stitches are being 
embroidered.
• Using a data design system, correct the thread 

density and overstitching settings in the 
embroidery data.

190

The thread is not cut automatically.

Lint or dust has accumulated around the needle 
plate (moving knife, fixed knife or thread retaining 
plate).

174

A bobbin case designed specifically for this 
machine is not used.
• Use the correct bobbin case.

—

Lint or dust has accumulated in the thread 
tension disc.

176

After the threads are automatically cut, the upper 
thread is too short and comes out of the needle.

Lint or dust has accumulated around the needle 
plate (moving knife, fixed knife or thread retaining 
plate).

174

Symptom

Probable Cause/Remedy

Page

Summary of Contents for PR1055X









































































































































































































Reviews:

No comments

Related manuals for PR1055X

Happy HK634020XB Maintenance Manual preview
HK634020XB
Brand: Happy Pages: 30
Baby Lock Ellageo PLUS BLL2 Quick Reference Manual preview
Ellageo PLUS BLL2
Brand: Baby Lock Pages: 43
Baby Lock Diana BL480A Instruction And Reference Manual preview
Diana BL480A
Brand: Baby Lock Pages: 71
Baby Lock BL50A Getting To Know preview
BL50A
Brand: Baby Lock Pages: 2
Baby Lock BL50A Quick Reference Manual preview
BL50A
Brand: Baby Lock Pages: 2
Baby Lock A_LINE Maria BL23A Instruction And Reference Manual preview
A_LINE Maria BL23A
Brand: Baby Lock Pages: 78
Baby Lock A-LINE Natalie BL18A Instruction And Reference Manual preview
A-LINE Natalie BL18A
Brand: Baby Lock Pages: 70
Baby Lock A-LINE Lauren BL450A Getting To Know Manual preview
A-LINE Lauren BL450A
Brand: Baby Lock Pages: 12
Baby Lock Aventura BLMAV Instruction And Reference Manual preview
Aventura BLMAV
Brand: Baby Lock Pages: 204
Baby Lock Aventura BLMAV Quick Reference Manual preview
Aventura BLMAV
Brand: Baby Lock Pages: 24
Baby Lock Elissimo & Elissimo GOLD BLSO-BF2 Quick Reference Manual preview
Elissimo & Elissimo GOLD BLSO-BF2
Brand: Baby Lock Pages: 22
Bartell B424 Owner'S Manual And Parts Book preview
B424
Brand: Bartell Pages: 30
Necchi Supernova Instructions Manual preview
Supernova
Brand: Necchi Pages: 122
Handiquilter HQ Sweet Sixteen Service Manual preview
HQ Sweet Sixteen
Brand: Handiquilter Pages: 41
handi quilter HQ Amara 20 Quick Reference Card preview
HQ Amara 20
Brand: handi quilter Pages: 2
VeriFone VX 805 Manual preview
VX 805
Brand: VeriFone Pages: 40
TAJIMA TFHX Series User Manual preview
TFHX Series
Brand: TAJIMA Pages: 140
Superabrasive LAVINA ELITE 3213EHV User Manual preview
LAVINA ELITE 3213EHV
Brand: Superabrasive Pages: 42

Brands by name

Popular brands

Load more brands