Brother PR1055X Operation Manual Download Page 67

Page: 67 / 200

BASIC EMBROIDERY

Loosen the two left thumb screws on the embroidery
frame holder.

If the screw is too tight, please use the included 3 way
screwdriver.

Left arm

Thumb screws



The left arm of the embroidery frame holder can be
moved.

• Only loosen the thumb screws a maximum of 2 turns

counterclockwise. Do not remove the screw.

Move the left arm to align the screw on the right side
with the mark for the embroidery frame to be installed,
and then tighten the thumb screws.

For this example, align the small thumb screw with
mark

Mark for extra-large embroidery frame
360 mm (W) × 200 mm (H)
(14 inches (W) × 7-7/8 inches (H))

Mark for extra-large embroidery frame
300 mm (W) × 200 mm (H)
(11-3/4 inches (W) × 7-7/8 inches (H)) (optional)

Mark for large embroidery frame
180 mm (W) × 130 mm (H)
(7-7/8 inches (W) × 5-1/8 inches (H))

Mark for medium embroidery frame
100 mm (W) × 100 mm (H)
(4 inches (W) × 4 inches (H))

Mark for small embroidery frame
60 mm (W) × 40 mm (H)
(2-3/8 inches (W) × 1-1/2 inches (H))



The embroidery frame holder is ready for the
embroidery frame to be attached.

Hold the embroidery frame level, and then
simultaneously align both the left and right mounts
with the embroidery frame holder clips.

• The inner frame should be on top.

Insert the embroidery frame until it snaps into place.

Make sure that the pins on the left and right arms of the
embroidery frame holder fit into the positioning slot and
hole on the embroidery frame.

Correctly using the embroidery frames

Various types of embroidery frames can be used with this
machine to suit your project.

In addition to the included embroidery frames, there are many
frames that can be used with this machine. (Refer to “Optional
accessories” on page 14.)

Note

• Please firmly tighten the two thumb screws with

included 3 way screwdriver. If the thumb screws
are not tightened, any of the following problems
may occur.

- The machine will detect the embroidery frame

size incorrectly.

- The starting position for the embroidery frame is

misaligned.

- The embroidery pattern is misaligned.

CAUTION

• Only use embroidery frames of the sizes

indicated in the screen, otherwise the
embroidery frame may hit the presser foot,
which may result in injuries.

Summary of Contents for PR1055X









































































































































































































Search results

Summary of Contents for PR1055X

Reviews:

Related manuals for PR1055X

Brands by name

Popular brands

Brother PR1055X, Operation Manual

Search results

Summary of Contents for PR1055X

Reviews:

Related manuals for PR1055X

Brands by name

Popular brands