Brother PR1055X Operation Manual Download Page 54

Page: 54 / 200

■

Embroidering the pattern repeatedly

After creating the repeated pattern, rehoop the embroidery
frame and keep embroidering for the next pattern.

Create the repeated pattern with the thread mark at
the center of the end of the pattern. (page 51)

Touch , ,

then .

Touch

, and then press the “Start/Stop”

button to start embroidering.



When embroidering is finished, the thread mark is
embroidered with the last thread color.

Remove the embroidery frame.

Rehoop the fabric in the embroidery frame.

Attach the embroidery frame to the machine, and then
touch

in the embroidering settings screen.

Touch .

Touch

to set the starting point to the left side of

the pattern.

Touch .

Memo

• Using the optional magnetic sash frame, the fabric

can be easily rehooped without removing the frame
from the machine. For details, refer to the manual
included with magnetic sash frame.

Note

• Adjust the position of the fabric so that the

embroidering area for the next pattern is within the
embroidering area of the embroidery sheet.

Pattern embroidered first

Position of pattern to be embroidered next

Embroidering area of embroidery sheet

Summary of Contents for PR1055X









































































































































































































Search results

Summary of Contents for PR1055X

Reviews:

Related manuals for PR1055X

Brands by name

Popular brands

Brother PR1055X, Operation Manual

Search results

Summary of Contents for PR1055X

Reviews:

Related manuals for PR1055X

Brands by name

Popular brands