Brother PR1055X Operation Manual Download Page 58

Page: 58 / 200

[Manual] setting for [Gradient]

You can select one color to be used in the [Gradient] effect.
The effect will be created with the color you select.

Select a color from the palette.

Selected color is displayed.

Touch .

Select the color scheme from samples.

Touch

to add the new schemes.

Touch to review the previous schemes.

Check the displayed color scheme, and then touch

: Return to the previous screen.

: Display the other color schemes.



The change thread color screen will appear.

Touch

to display to the pattern editing screen.

Memo

• To temporarily register your favorite schemes,

touch

(to release your favorite schemes, touch

again). 9 color schemes can be saved on the

page*. Touch

to check the registered

favorite schemes. To cancel the registration, touch

* Maximum 20 pages of schemes can be reviewed.

Summary of Contents for PR1055X









































































































































































































Search results

Summary of Contents for PR1055X

Reviews:

Related manuals for PR1055X

Brands by name

Popular brands

Brother PR1055X, Operation Manual

Search results

Summary of Contents for PR1055X

Reviews:

Related manuals for PR1055X

Brands by name

Popular brands