Brother PR1055X Operation Manual Download Page 35

Page: 35 / 200

BASIC EMBROIDERY

Basic embroidering procedures are described below.
Check the overall procedure below, before operating the
machine.

When the machine is purchased, only the bobbin case is
installed in the hook. Insert a bobbin wound with bobbin
thread for embroidering.

Removing the bobbin case

Open the hook cover.

Pull the hook cover toward you.

Pull the thread picker toward you if it was not pulled
toward the front.

To gain access to the bobbin case easily, pull the thread
picker toward front.

Chapter

BASIC EMBROIDERY

BASIC PROCEDURES

Step

Operation

Reference

Page

Install the bobbin.

Turn on the machine.

Select an embroidery pattern.

Edit the embroidery pattern.

Check the previewed image.

Hoop the fabric in the embroidery
frame.

Attach the embroidery frame to the
machine.

Specify the embroidering settings.

Check the embroidery area.

Thread the upper threads.

Touch the “Start/Stop” button to start
embroidering.
(Once embroidering is completed, the
machine automatically stops.)

Remove the embroidery frame.

Turn off the machine.

INSTALLING THE BOBBIN

CAUTION

• Be sure to use prewound bobbins (Fil-Tec/

TRU-SEW POLYESTER “Filaments”) or metal
bobbins designed specifically for this machine.

• When winding a bobbin, use optional bobbin

winder (page 142) and metal bobbins.

Note

• Before starting to embroider make sure that there

is enough bobbin thread for the pattern.

• Make sure to clean the bobbin case every time the

bobbin is changed. (page 175)

Thread picker

Memo

• Thread picker is a device that is used to hold the

thread when beginning to embroider or when
trimming the thread.

Summary of Contents for PR1055X









































































































































































































Search results

Summary of Contents for PR1055X

Reviews:

Related manuals for PR1055X

Brands by name

Popular brands

Brother PR1055X, Operation Manual

Search results

Summary of Contents for PR1055X

Reviews:

Related manuals for PR1055X

Brands by name

Popular brands