Brother DCP Series Service Manual Download Page 185

Page: 185 / 309

3-77

Confidential

9.17 CR Encoder Strip / Encoder Strip Guard Film

CR encoder strip

(1) On the left end of the CR frame, press the rear end of the Encoder strip spring inward

and release the left and right end of the CR encoder strip from the hook.

(2) Rotate the CR encoder strip in the direction of the arrow shown below. Remove it after

aligning the left end square opening with the boss-shape of the strip support.

Note

Be careful not to damage the CR encoder strip. If the strip is stained or damaged,

replace it with a new one.

(3) Detach the Encoder strip spring.

Assembling Note

Attach the CR encoder strip with the end with the mark on the right

(Carriage motor side) and the mark facing upward. (Refer to the illustration above)

(3_055L)

CR encoder strip

Pointing upward

Strip support

CR frame

Encoder stop

spring

Summary of Contents for DCP Series






















































































































































































































































































































Search results

Summary of Contents for DCP Series

Reviews:

Related manuals for DCP Series

Brands by name

Popular brands

Brother DCP Series, Service Manual

Search results

Summary of Contents for DCP Series

Reviews:

Related manuals for DCP Series

Brands by name

Popular brands