Brother DCP Series Service Manual Download Page 165

Page: 165 / 309

3-57

Confidential

(20) Remove the Document scanning position sensor holder ASSY from Document feed

roller 1 and 2.

(21) Remove Document feed roller 1 and 2 by pulling them away from bearings then

remove it from the ADF unit.

(22) Remove the three pinch rollers from the ADF unit.

(23) Turn the ADF unit upside down then press the ADF unit hook. Remove the LF1

support plate by sliding it to the rear.

(24) Release the 2 tabs of the Document separate roller ASSY and remove it from the ADF

unit.

Assembling Note

Before installing the Document separate roller ASSY to the ADF unit,

refer to

Section 5

in this chapter and apply the specified lubricant to all roller shafts.

(3_077)

Pinch roller

ADF unit

Document scanning position

sensor holder ASSY

Document feed roller 2

Document feed roller 1

Bearing

(Rear)

(Right)

(3_121)

LF1 support plate

Document separate roller ASSY

ADF unit

Tab

(Rear)

Release the hook

Summary of Contents for DCP Series






















































































































































































































































































































Search results

Summary of Contents for DCP Series

Reviews:

Related manuals for DCP Series

Brands by name

Popular brands

Brother DCP Series, Service Manual

Search results

Summary of Contents for DCP Series

Reviews:

Related manuals for DCP Series

Brands by name

Popular brands