Brother DCP Series Service Manual Download Page 135 | Manualshive

Page: 135 / 309

background image

3-27

Confidential

9.3

Head Joint Rubber / CR Timing Belt / Head/Carriage Unit

During disassembly, leave the Head/carriage unit attached to the machine except when
removing the Ink refill ASSY or Engine unit (including the Maintenance unit).

<Ink Cartridge Model only>
When removing the Head/carriage unit, Ink refill ASSY or Engine unit, you need to remove
beforehand all four Ink cartridges and set the Protective part instead (refer to

Insert the Protective part firmly until it hooks on to the right side to prevent ink from leaking
from the Ink supply tube and staining the machine.

Note

• When replacing the Head/carriage unit, put on a grounding wrist band and perform

the job on a static mat. Also take care not to touch the conductor sections on the
flat cables.

• During the removal or installation job for the Head/carriage unit, take care not to

contaminate the CR encoder strip or PF encoder disk with ink or grease.

(1) Plug the Power cord into an electrical outlet.

(2) Enter Maintenance mode, then enter [6], [3], [Mono Start], and [*] in that order; the

Head/carriage unit automatically moves to the position shown in the figure.

(3) Open the Document scanner unit until it locks.

(3_019L)

Head/carriage unit

Document scanner unit

Scanner cover support

«
...
133
134
135
136
137
...
»

Summary of Contents for DCP Series






















































































































































































































































































































Reviews:

No comments

Related manuals for DCP Series

Brand: VASTEX Pages: 15

Brand: Wang Pages: 24

WorkCentre 7232

Brand: Xerox Pages: 13

Brand: Xerox Pages: 4

Brand: Samsung Pages: 549

Brand: Pinnacle Technology Pages: 76

Multi-Font NX-2415

Brand: Star Micronics Pages: 134

Fast T-Jet Blazer Pro

Brand: Screen Print & Inkjet Pages: 138

Brand: Xerox Pages: 34

Brand: Linux Pages: 8

Brand: Konica Minolta Pages: 102

Brand: Yurex Pages: 29

imagePRESS V1000

Brand: Canon Pages: 123

Brand: Domino Pages: 114

Brand: DataCard Pages: 4

Brand: Oce Pages: 196

Brand: Hitachi Pages: 11

Brand: Hitachi Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands