Brother DCP Series Service Manual Download Page 201

Page: 201 / 309

3-93

Confidential

9.29 Base Pad on Paper Tray ASSY

(1) When there is a need to replace the Base pad, peel it off from the bottom of the Paper

tray.

Note

Once removed, the Base pad will become unusable and will need to be replaced with

a new one.

Assembling Note

When attaching a new Base pad to the Paper tray, align the front end of

the pad with the front end of the depression, and the left and right position with the center
of the depression, as shown above.

(3_078L)

Base pad

Depression

Base pad

Paper tray

Align the Base pad edge with

the front end of the

depression (this line) at the

bottom of the Paper tray.

Paper tray

Summary of Contents for DCP Series






















































































































































































































































































































Search results

Summary of Contents for DCP Series

Reviews:

Related manuals for DCP Series

Brands by name

Popular brands

Brother DCP Series, Service Manual

Search results

Summary of Contents for DCP Series

Reviews:

Related manuals for DCP Series

Brands by name

Popular brands