Brother DCP Series Service Manual Download Page 266 | Manualshive

Page: 266 / 309

background image

5-44

Confidential

1.4.23 Traveling Speed Check of Head/Carriage Unit (Maintenance mode 69)

<Function>

This function checks whether the traveling speed of the Head/carriage unit is within the
specified range.

<Operating Procedure>

(1) Enter [6] and [9] in the initial stage of the maintenance mode.

The machine shows "CR AGING" on the LCD and starts checking the traveling speed
of the Head/carriage unit.
In each of travel speeds of 43.3, 26.7 and 21.7 inches/second (ips), the machine
checks whether the maximum and minimum traveling speeds of the Head/carriage unit
are within the specified range.

- If the maximum and minimum speeds in all of the three traveling speeds are within

the specified range, "430 270 210" appears on the LCD.

- If any one is out of the range, the machine shows some message, e.g., "430 270

21X," on the LCD. This sample message indicates that the speed variation is within
the allowable range when the Head/carriage unit travels at 43.3 and 26.7 inches/
second; however, it is out of the range at 21.7 inches/second.

(2) Press [Stop] or [X] to return the machine to the initial stage of the maintenance mode.

«
...
264
265
266
267
268
...
»

Summary of Contents for DCP Series






















































































































































































































































































































Reviews:

No comments

Related manuals for DCP Series

Brand: Magicard Pages: 6

Brand: Valentin Pages: 96

Brand: Panasonic Pages: 169

Brand: Oki Pages: 118

Brand: Oki Pages: 126

Brand: Xerox Pages: 8

Brand: Oki Pages: 349

Brand: Canon Pages: 2

Brand: Canon Pages: 2

Brand: Oce Pages: 222

ColorQube 87 Series

Brand: Xerox Pages: 32

Brand: Ricoh Pages: 2

Accel-a-Writer 8200

Brand: Xante Pages: 12

Jetrix LXi Series

Brand: InkTec Pages: 3

Brand: Konica Minolta Pages: 108

Brand: SNBC Pages: 52

Brand: Ice Pages: 133

8560/SDN - Phaser Color Solid Ink Printer

Brand: Xerox Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands