Brother DCP Series Service Manual Download Page 270 | Manualshive

Page: 270 / 309

background image

5-48

Confidential

1.4.25 Move of the Head/Carriage Unit to the Center (Maintenance mode 75)

<Function>

This function is used to remove paper particles and dust accumulated between the
maintenance unit and Head/carriage unit. Using this function moves the Head/carriage unit
to the center of its travel, allowing you to easily remove the paper particles and dust
accumulated.

<Operating Procedure>

(1) Enter [7] and [5] in the initial stage of the maintenance mode.

The machine displays "PLS OPEN COVER" on the LCD.
The Head/carriage unit moves to the center of its travel.

(2) Open the document scanner unit.

The machine displays "PLS CLOSE COVER" on the LCD.

(3) Remove the paper particles and dust accumulated.

(4) Close the document scanner unit.

The Head/carriage unit returns to the home position, then the machine returns to the
initial stage of the maintenance mode.

Tip

In standby state, holding down [Stop] or [X] continuously for at least five seconds

with the document scanner unit open can also move the Head/carriage unit in the
same manner as above.

«
...
268
269
270
271
272
...
»

Summary of Contents for DCP Series






















































































































































































































































































































Reviews:

No comments

Related manuals for DCP Series

SCX-4300 - SCX 4300 B/W Laser

Brand: Samsung Pages: 97

SCX 4828FN - Laser Multi-Function Printer

Brand: Samsung Pages: 151

SCX 4725FN - B/W Laser - All-in-One

Brand: Samsung Pages: 120

SCX 4500 - B/W Laser - All-in-One

Brand: Samsung Pages: 97

SCX 4200 - B/W Laser - All-in-One

Brand: Samsung Pages: 95

SCX 4500 - B/W Laser - All-in-One

Brand: Samsung Pages: 172

ProXpress M337x

Brand: Samsung Pages: 56

PROXPRESS M332 SERIES

Brand: Samsung Pages: 50

ML-2240 - 23 Ppm Mono Laser Printer

Brand: Samsung Pages: 82

Brand: Samsung Pages: 8

ML-1610 - B/W Laser Printer

Brand: Samsung Pages: 134

ML-1610 - B/W Laser Printer

Brand: Samsung Pages: 112

Brand: Samsung Pages: 128

Brand: Samsung Pages: 152

ML 3471ND - B/W Laser Printer

Brand: Samsung Pages: 207

ML 2150 - B/W Laser Printer

Brand: Samsung Pages: 237

ML 3471ND - B/W Laser Printer

Brand: Samsung Pages: 103

ML 2150 - B/W Laser Printer

Brand: Samsung Pages: 217

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands