Brother DCP Series Service Manual Download Page 226

Page: 226 / 309

5-4

Confidential

Non-touch panel model

<Operating Procedure>

(1) When the machine is on standby, press [Menu], [Mono Start], and [Menu] in order. The

LCD will display "0

■■

MAINTENANCE

■

" and the machine will enter end-user

accessible maintenance mode.

(2) To select one of the maintenance mode functions, directly specify the maintenance

mode you want to use.

(3) When each of the maintenance mode functions is completed, the machine

automatically returns to standby.

Note

To stop the procedure midway and return the machine to standby, press [Stop].

1.2

Operations of the Keys in the Maintenance Mode

The operations of the keys used in the maintenance mode are different depending on the
panel specifications on the model.

1.2.1 Entering ten keys, [ ] or [ ] in the maintenance mode with models without these

keys

Press [ ] or [ ] to display desired letters on the LCD, and press [OK] to enter.

Summary of Contents for DCP Series






















































































































































































































































































































Search results

Summary of Contents for DCP Series

Reviews:

Related manuals for DCP Series

Brands by name

Popular brands

Brother DCP Series, Service Manual

Search results

Summary of Contents for DCP Series

Reviews:

Related manuals for DCP Series

Brands by name

Popular brands