Brother DCP Series Service Manual Download Page 169

Page: 169 / 309

3-61

Confidential

<Touch panel models>

(4) Release the connector lock and unplug the LCD flat cable from the main PCB ASSY.

Note

After disconnecting the LCD flat cable, check if the cable is not damaged at its end or

shortcircuited. When connecting LCD flat cables, do not insert them at an angle. After
insertion, check again that the cables are not at an angle.

(5) Remove the screw of the TAPTITE CUP S M3x6 and remove the FG wire from the

cable guide.

Assembling Note

Route the FG wire along the cable guide (marked by the dotted circle)

as shown above.

(6) Remove the two screws of the TAPTITE CUP B M3x10, release the 2 bosses, and

remove the bottom panel cover.

(7) Release two bosses and remove the control panel ASSY.

(3_088L)

Cable guide

TAPTITE CUP S M3x6

FG wire

(3_089L)

Boss

TAPTITE CUP S M3x10

Front center cover

Boss

Control panel ASSY

Bottom panel cover

TAPTITE CUP S

M3x10

Summary of Contents for DCP Series






















































































































































































































































































































Search results

Summary of Contents for DCP Series

Reviews:

Related manuals for DCP Series

Brands by name

Popular brands

Brother DCP Series, Service Manual

Search results

Summary of Contents for DCP Series

Reviews:

Related manuals for DCP Series

Brands by name

Popular brands