Brother DCP Series Service Manual Download Page 215 | Manualshive

Page: 215 / 309

background image

4-14

Confidential

1) Check the block number with the least uneven printing within the configuration

block (bottom). Using a spanner, turn the external inclination adjuster knob
according to the checked number.
For example, when +2 block print unevenness is the smallest, turn the external
inclination adjuster knob two notch clockwise. If the smallest number is -2 block,
turn the external inclination adjuster knob two notch counter-clockwise.

2) After making adjustments, proceed to Step (8).
When the block number with the least uneven printing in the configuration block (top)
is not "0"
1) Check the block number with the least uneven printing within the configuration

block (top). Using an Allen wrench, turn the internal inclination adjuster knob
according to the checked number.
For example, when +1Right block print unevenness is the smallest, turn the
internal inclination adjuster knob 90 degrees clockwise. If the smallest number is
Left-1 block, turn the inclination adjuster knob 90 degrees counter-clockwise.

2) Close the document scanner unit and print the test pattern for inclination

adjustment again in the same manner as Step (6).

3) Perform

Chapter 5 "1.4.19 Move of the Head/Carriage Unit to the Adjustment

Position (Maintenance mode 63)"

to move the Head/carriage unit to an adjusted

position. Open the document scanner unit.

4) Check the block number with the least uneven printing within the configuration

block (bottom). Using a spanner, turn the external inclination adjuster knob
according to the checked number.
For example, when +2 block print unevenness is the smallest, turn the external
inclination adjuster knob two notch clockwise. If the smallest number is -2 block,
turn the external inclination adjuster knob two notch counter-clockwise.

(8) Close the document scanner unit after adjustments.

The Head/carriage unit will return to its home position.

(9) Print the test pattern in step (6) again and confirm that the block number with the least

uneven printing in the top and bottom configuration block is "0".
When the block number with the least uneven printing is not "0", repeat the adjustment
from step (1).

KHDGBSRVLWLRQB/

Head/carriage unit

Inclination adjuster

knob (external)

Head cover

«
...
213
214
215
216
217
...
»

Summary of Contents for DCP Series






















































































































































































































































































































Reviews:

No comments

Related manuals for DCP Series

iP2600 - PIXMA Color Inkjet Printer

Brand: Canon Pages: 2

Brand: Canon Pages: 8

ImageCLASS 2300

Brand: Canon Pages: 102

Brand: Canon Pages: 18

Brand: Canon Pages: 16

Brand: Canon Pages: 39

Brand: Canon Pages: 2

Brand: Canon Pages: 73

Brand: Canon Pages: 29

Brand: Canon Pages: 16

Brand: Canon Pages: 44

Brand: Canon Pages: 60

Brand: Olympus Pages: 236

I450 - i 450 Color Inkjet Printer

Brand: Canon Pages: 13

Brand: TallyGenicom Pages: 310

Brand: TallyGenicom Pages: 330

Brand: Oce Pages: 192

Brand: Oce Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands