Series
Photo Printer
Start Here
Easy Setup Instructions
1
Unpack the Printer
2
Prepare the Printer
3
Install the FINE Cartridges
4
Align the Print Head (FINE Cartridge)
Carefully remove all items from the box.
PIXMA iP6310D Photo Printer
Power Cord
Color FINE Cartridge
(CL-41)
Photo FINE Cartridge
(CL-52)
Documentation and
Software Kit
1
Remove the shipping tape from the front and back of the
printer.
2
Open (a) the card slot cover first and (b) the front cover next,
Pull down and remove the protective material on the right
side.
3
Close the front cover first and the card slot cover next.
4
Plug the power cord into the back of the printer and connect
the other end to a power outlet.
Press the
POWER
button. The printer will initialize. Wait until
the
POWER
lamp remains fully lit.
NOTE:
Do not connect the USB cable at this stage.
5
When the screen appears on the LCD, confirm a language
and then press the
OK
button.
NOTE:
•
If the language you want to be displayed is not selected, refer to
"An Unintended Language is Displayed on the LCD" in the
Direct
Printing Guide
.
•
If you leave the printer more than five minutes without using any
button on the operation panel, the LCD goes into sleep mode
automatically. Press the
OK
button to turn on the LCD again.
6
Open the card slot cover first and the front cover next.
The FINE Cartridge holder automatically moves to the left.
Write down the serial number. You will need this to register
the product.
1
Take out the Color FINE Cartridge (CL-41) from its box and remove the protective
tape gently.
NOTE:
•
Do not touch the electrical contacts or print head nozzles on a FINE Cartridge. The
printer may not print out properly if you touch it.
•
Do not reattach the protective tape once you have removed it.
•
Handle the removed protective tape carefully to avoid getting your hands dirty or
staining surrounding work area.
2
Insert the Color FINE Cartridge slightly slanted into the left slot (C).
3
Push up the Color FINE Cartridge until it clicks into place.
IMPORTANT:
For correct printer operation, make sure the FINE Cartridge is secure in
slots.
4
Repeat the procedure for the Photo FINE Cartridge (CL-52), inserting it into the
right slot (P).
5
Close the front cover first and the card slot cover next.
IMPORTANT:
Wait until the preparatory operation is complete; this takes about one
to two minutes.
The message requesting head alignment is displayed on the LCD.
Go to the next step.
1
Open the paper support and pull out the paper output tray.
2
Pinch the paper guide and slide it to the left. Load a few
sheets of blank paper into the auto sheet feeder, then slide
the paper guide toward the left edge of the paper.
NOTE:
Ensure that the paper thickness lever is set to the left
position.
3
Ensure that the message requesting head alignment is
displayed on the LCD, select
YES
using the
buttons and
press the
OK
button.
The pattern is printed. And the print head is aligned
automatically.
IMPORTANT:
It takes about four minutes to finish printing.
When automatic print head alignment can not be
executed correctly, the message "
HEAD ALIGNMENT
ERROR
" is displayed on the LCD. refer to
"
An Error
Message is Displayed in the LCD
" in the
Direct Printing
Guide
.
Continue with Step 5
on side two.
To the FINE Cartridge holder
FINE Cartridge
holder
Paper thickness lever
Protective material
Power cord
Serial number
Protective tape
Paper support
Paper output tray
(b) Front cover
Paper guide
Print side
Auto sheet feeder
Print head nozzles
Electrical contacts
(a) Card slot cover
iP6310D̲ESI̲US̲V1.indd 1
iP6310D̲ESI̲US̲V1.indd 1
2006/05/09 9:54:03
2006/05/09 9:54:03
