manualshive.com logo in svg

Brocade Communications Systems DCX 8510-8, Hardware Reference Manual

Share
Download
Brocade Communications Systems DCX 8510-8 Hardware Reference Manual Download Page 5

Time and items required..................................................................... 92
Faulty core switch blade indicators..................................................... 92
Removing a core switch blade (CR16-8)............................................ 92
Replacing a core switch blade (CR16-8).............................................94

Power supply removal and replacement......................................................... 95

Time and items required..................................................................... 95
Identifying power supplies...................................................................95
Removing a power supply...................................................................96
Replacing a power supply................................................................... 97

Blower assembly removal and replacement................................................... 98

Time and items required..................................................................... 98
Removing a blower assembly ............................................................ 98
Replacing a blower assembly............................................................. 99

WWN card removal and replacement............................................................. 99

Time and items required................................................................... 100
Verifying the need for replacement................................................... 100
Preparing for the WWN card replacement........................................ 100
Removing the WWN card and WWN bezel (logo plate)....................101
Replacing the WWN card and WWN bezel (logo plate)....................103

Transceiver removal and replacement..........................................................103

Time Required...................................................................................104
Items Required..................................................................................104
Removing an SFP+ transceiver........................................................ 104
Replacing an SFP+ transceiver.........................................................105
Removing and replacing an mSFP optical transceiver..................... 106
Removing and replacing a QSFP optical transceiver........................107
Qualified transceivers for the FC16-64 port blade and the core

blades.......................................................................................... 108

Inter-chassis link (ICL) cable removal and replacement............................... 108

Time and items required................................................................... 110
Removing an ICL cable.....................................................................110
Replacing an ICL cable..................................................................... 110
Possible ICL configurations...............................................................110

Brocade DCX 8510-8 chassis removal and replacement............................. 113

Time and items required................................................................... 114
Faulty Brocade DCX 8510-8 chassis indicators................................114
Recording critical Brocade DCX 8510-8 and SAN information......... 115
Disconnecting from network and fabric............................................. 117
Removing components from the chassis.......................................... 118
Installing the replacement chassis.................................................... 118
Installing components into the new chassis...................................... 119
Downloading the configuration..........................................................120
Verifying correct operation of system................................................120
Reconnecting the system to the network and fabric......................... 122
Verifying correct configuration of the fabric.......................................122
Cable routing table............................................................................ 123

Application and Encryption Blades........................................................................................127

Introduction................................................................................................... 127
FS8-18 blade.................................................................................................127
FX8-24 blade.................................................................................................127
FCOE10-24 blade......................................................................................... 129

Limitations of FCOE10-24 blade....................................................... 130

Diagnostics and Troubleshooting.......................................................................................... 131

Introduction................................................................................................... 131

Brocade DCX 8510-8 Backbone Hardware Reference Manual

5

53-1002180-08

Summary of Contents for DCX 8510-8

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands