manualshive.com logo in svg

Brocade Communications Systems DCX 8510-8, Hardware Reference Manual

Share
Download
Brocade Communications Systems DCX 8510-8 Hardware Reference Manual Download Page 105

The 16 Gbps SFP+ transceivers have an attached pull tab like the mSFPs. Instead of using the tool,
simply grasp the pull tab and pull straight out to remove the 16 Gbps SFP+ from the switch or blade.
Refer to the illustration for the mSFP transceiver for the basic appearance of the 16 Gbps
transceiver.

FIGURE 32

 Replacing an optical transceiver

1. SFP/XFP bail

FIGURE 33

 Replacing a 16 Gbps SFP+ optical transceiver

Replacing an SFP+ transceiver

Complete the following steps to replace an SFP+ transceiver.

1. Making sure that the bail (wire handle) is in the unlocked position, position the optical transceiver so

that the key is oriented correctly to the port. Insert the transceiver into the port until it is firmly seated
and the latching mechanism clicks; then close the bail.

The 16 Gbps SFP+ transceivers do not have bails. Use the tab on the 16 Gbps SFP+ transceivers to
help gently push the transceiver into the port. Do not push so hard as to bend the tab.

Replacing an SFP+ transceiver

Brocade DCX 8510-8 Backbone Hardware Reference Manual

105

53-1002180-08

Summary of Contents for DCX 8510-8

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands