manualshive.com logo in svg

Brocade Communications Systems DCX 8510-8, Hardware Reference Manual

Share
Download
Brocade Communications Systems DCX 8510-8 Hardware Reference Manual Download Page 36

FIGURE 6

 Configuration tasks

Establishing a serial connection to the Brocade DCX 8510-8

To establish a serial connection to the console port on the Brocade DCX 8510-8, complete the
following steps.

1. Verify that the Brocade DCX 8510-8 is powered on and that POST is complete by verifying that all

power LED indicators on the port, control processor, and core switch blades display a steady green
light.

2. Remove the shipping cap from the CONSOLE port on the active CP. Use the serial cable provided

with the Brocade DCX 8510-8 to connect the CONSOLE port on the active CP to a computer
workstation. The active CP blade is indicated by an illuminated (blue) LED.

Establishing a serial connection to the Brocade DCX 8510-8

36

Brocade DCX 8510-8 Backbone Hardware Reference Manual

53-1002180-08

Summary of Contents for DCX 8510-8

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands