Brocade Communications Systems DCX 8510-8 Hardware Reference Manual Download Page 4

Page: 4 / 176

Establishing an Ethernet connection to the Brocade DCX 8510-8............... 39
Customizing a switch name.......................................................................... 40
Customizing a chassis name........................................................................ 40
Setting the domain ID....................................................................................40
Setting the date and time.............................................................................. 41

Setting the date.................................................................................41
Setting the time zone........................................................................ 41
Synchronizing local time................................................................... 42

Verifying the PID mode................................................................................. 43
Determining installed software licenses........................................................43
Installing transceivers and attaching cables................................................. 43

Installing SFP+ and mSFP transceivers and cables......................... 44
Qualified transceivers for the FC16-64 port blade and the core

blades..........................................................................................44

Installing QSFP transceivers and cables.......................................... 45

Managing cables...........................................................................................46
Verifying correct operation and backing up the configuration....................... 47
Powering off the Brocade DCX 8510-8.........................................................48

Monitoring System Components............................................................................................49

Monitoring overview...................................................................................... 49
Determining the status of a port or application blade....................................54

Blade illustrations..............................................................................54

Determining the status of a control processor blade (CP8).......................... 65
Determining the status of a core switch blade (CR16-8).............................. 67
Determining the status of a power supply.....................................................69
Determining the status of a blower assembly............................................... 70
Determining the status of a WWN card.........................................................72

Removal and Replacement Procedures................................................................................. 75

Introduction................................................................................................... 75
ESD precautions........................................................................................... 75
Chassis door removal and replacement....................................................... 76

Time and items required................................................................... 76
Removing a chassis door..................................................................76
Replacing a chassis door..................................................................77

Cable management comb removal and replacement................................... 77

Time and items required................................................................... 77
Removing a cable management comb..............................................77
Replacing a cable management comb..............................................78

Port, application, and encryption blade removal and replacement............... 78

Time and items required................................................................... 79
Removing a blade............................................................................. 80
Replacing a blade............................................................................. 81

Blade filler panel removal and replacement..................................................82

Removing a filler panel......................................................................82
Replacing a filler panel......................................................................83

Control processor blade (CP8) removal and replacement............................84

Core switch blade (CR16-8) removal and replacement................................ 92

Brocade DCX 8510-8 Backbone Hardware Reference Manual

53-1002180-08

Summary of Contents for DCX 8510-8

















































































































































































Search results

Summary of Contents for DCX 8510-8

Reviews:

Related manuals for DCX 8510-8

Brands by name

Popular brands

Brocade Communications Systems DCX 8510-8, Hardware Reference Manual

Search results

Summary of Contents for DCX 8510-8

Reviews:

Related manuals for DCX 8510-8

Brands by name

Popular brands