Brocade Communications Systems DCX 8510-8 Hardware Reference Manual Download Page 15

Page: 15 / 176

‐

The 16-Gbps QSFPs supported on FC16-64 prot blade auto-negotiate at 4, 8, and
16 Gbps.

‐

The 16-Gbps QSFPs based inter-chassis link (ICL) on the core blades run at 64
Gbps (four fixed 16-Gbps clustered in a single quad connector and cable).

• Blades that are serviced from the port side of the Brocade DCX 8510-8. Blowers, power supplies,

and power cables that are serviced from the nonport side.

• World Wide Name (WWN) cards on the nonport side, to maintain chassis-specific information such

as WWNs, IP addresses, and summary status information of each port blade and power supply
through LEDs.

• Redesigned cable management comb and chassis door.

Port side of the Brocade DCX 8510-8

NOTE

Airflow in the Brocade DCX 8510-8 is from the nonport (noncable) side to the port (cable) side and out
the exhaust vent.

Port side of the Brocade DCX 8510-8

Brocade DCX 8510-8 Backbone Hardware Reference Manual

53-1002180-08

Summary of Contents for DCX 8510-8

















































































































































































Search results

Summary of Contents for DCX 8510-8

Reviews:

Related manuals for DCX 8510-8

Brands by name

Popular brands

Brocade Communications Systems DCX 8510-8, Hardware Reference Manual

Search results

Summary of Contents for DCX 8510-8

Reviews:

Related manuals for DCX 8510-8

Brands by name

Popular brands