Brocade Communications Systems DCX 8510-8 Hardware Reference Manual Download Page 84 | Manualshive

Page: 84 / 176

background image

Control processor blade (CP8) removal and replacement

This document describes how to remove and replace a control processor (CP8) blade. Each chassis
has two CP8 blades. In the DCX 8510-8, they are located in slots 6 and 7.

NOTE

The CP8 blade is compatible only with the Brocade DCX Backbones (including the DCX 8510
Backbones).

NOTE

The Brocade firmware upgrade policy for CP8 blades specifies testing for the current Fabric OS
release and one version earlier. It is possible to upgrade by more than one version, but it is a very
specific and detailed process. Read the directions under

Downloading firmware from an FTP server

page 89 or

Downloading firmware from a USB device

on page 90 carefully.

NOTE

If the new CP blade does not have the same firmware as the active CP blade, the new blade must be
upgraded to the same firmware version. You can determine the firmware version on the replacement
blade and perform a firmware upgrade if necessary after inserting the blade in the chassis, but you
must disable high availability (HA) before inserting the new blade. If the new CP blade is severely
down-level, a very specific procedure must be followed to bring the blade up to the correct firmware
version.

Time and items required

The replacement procedure for the CP blade takes approximately 30 minutes. The following items are
required for the CP blade replacement:

• Electrostatic discharge (ESD) grounding strap
• Workstation computer
• Serial cable
• IP address of an FTP server for backing up the Brocade DCX 8510-8 configuration
• #2 Phillips screwdriver
• Replacement Brocade DCX 8510-8 control processor blade (CP8)

If you are upgrading through multiple versions of the Fabric OS, consult the

Verifying operation of the

table to see which intermediate versions of the Fabric OS you might need. Plan

carefully and for extra time if this is your situation.

Faulty CP blade indicators

Confirm that you need to replace the CP blade. The following events may indicate that a CP blade is
faulty:

• The status LED on the CP blade is lit steady amber, or the power LED is not lit.
• The CP blade does not respond to Telnet commands, or the serial console is not available.
• The

slotShow

command does not show that the CP blade is enabled.

Control processor blade (CP8) removal and replacement

84

Brocade DCX 8510-8 Backbone Hardware Reference Manual

53-1002180-08

«
...
82
83
84
85
86
...
»

Summary of Contents for DCX 8510-8

















































































































































































Reviews:

No comments

Related manuals for DCX 8510-8

ML-2010 - B/W Laser Printer

Brand: Samsung Pages: 25

Brand: YOKOGAWA Pages: 22

NOP1840 PEP-Box

Brand: Newtec Pages: 96

3CRWPS10075-US - OfficeConnect Wireless 54Mbps 11g Print...

Brand: 3Com Pages: 94

Brand: Vxl Pages: 2

SuperServer 6019P-WT

Brand: Supermicro Pages: 133

InterServe 600 Series

Brand: Intergraph Pages: 104

Brand: Bodet Pages: 13

Brand: Huawei Pages: 39

Brand: Huawei Pages: 188

5288 V3 V100R003

Brand: Huawei Pages: 297

Brand: Huawei Pages: 2

Brand: Panasonic Pages: 17

Brand: Panasonic Pages: 42

Brand: Panasonic Pages: 316

Brand: Panasonic Pages: 456

Brand: TAG Pages: 84

Brand: Zonet Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands