manualshive.com logo in svg

Brocade Communications Systems DCX 8510-8, Hardware Reference Manual

Share
Download
Brocade Communications Systems DCX 8510-8 Hardware Reference Manual Download Page 154

System component

Description

UltraScale ICL bandwidth

Brocade DCX 8510-4: 1.024 Tbps; 16 UltraScale ICL ports provide the equivalent of
64 16-Gbps ports. Each UltraScale ICL port provides 64 Gbps bandwidth over a
QSFP (16 Gbps x 4) link.

Brocade DCX 8510-8: 2.048 Tbps; 32 UltraScale ICL ports provide the equivalent of
128 16-Gbps ports. Each UltraScale ICL port provides 64 Gbps bandwidth over a
QSFP (16 Gbps x 4) link.

Both models: Frame-based trunking is enabled between four UltraScale ICLs. DPS
distributes exchanges across all frame trunks.

Power inlet

C13; power from non-port side

Power supplies

Brocade DCX 8510-4 - Two hot-swappable 2000 W AC power supply modules
(100-240 VAC autosensing), 2N redundancy

Brocade DCX 8510-8 - Four modular, hot-swappable power supplies (100-240 VAC
autosensing)

Fans

Brocade DCX 8510-4 - Two fans per chassis

Brocade DCX 8510-8 - Three fans per chassis

Cooling

Brocade DCX 8510-4 - Two blower assembly modules (one required for operation);
rear panel-to-door airflow

Brocade DCX 8510-8 - Three blower assemblies; non-port (non-cable) side to the port
(cable) side airflow

System architecture

Nonblocking shared memory

System processors

FreeScale 8548, 1.2 GHz

Aggregate bandwidth

5 Tbps populated with four FC16-64 port blades and using 16 ICL ports @ 64 Gbps

Switch latency

FC8-32E, FC8-48E, and FC8-64 blades: <700 ns any port to any port local switching
and 2.1 μsec blade to blade at 8-Gbps, cut-through routing.

FC16-32, FC16-48, and FC16-64 blades: <700 ns any port to any port local switching
and 2.1 μsec blade to blade at 16-Gbps, cut-through routing.

FX8-24 blade - FC to FC: <2.1 μsec any port to any port at 8 Gbps, cut-through
routing.

FCOE10-24 blade - CEE to CEE (different ASIC) and FCoE to FC: <5 μsec any port
to any port at 8 Gbps, cut-through routing.

Maximum frame size

2112-byte payload

Frame buffers

8000 per Gen 5 ASIC, with 5000 more that can be borrowed from neighboring ASIC if
enabled

Brocade DCX 8510 Technical Specifications

154

Brocade DCX 8510-8 Backbone Hardware Reference Manual

53-1002180-08

Summary of Contents for DCX 8510-8

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands