Brocade Communications Systems DCX 8510-8 Hardware Reference Manual Download Page 97

Page: 97 / 176

FIGURE 28

Removal and replacement of the power supply

Replacing a power supply

To replace a power supply, complete the following steps.

1. If you are not replacing the power supply, insert a filler panel into the slot.
2. Otherwise, insert the power supply into the slot. Verify that the power supply is seated by gently

pulling on the handle.

3. Tighten the thumbscrew.
4. Replace the power cord.
5. Latch the power cord retainer clip.
6. Turn on the power switch.

Replacing a power supply

Brocade DCX 8510-8 Backbone Hardware Reference Manual

53-1002180-08

Summary of Contents for DCX 8510-8

















































































































































































Search results

Summary of Contents for DCX 8510-8

Reviews:

Related manuals for DCX 8510-8

Brands by name

Popular brands

Brocade Communications Systems DCX 8510-8, Hardware Reference Manual

Search results

Summary of Contents for DCX 8510-8

Reviews:

Related manuals for DCX 8510-8

Brands by name

Popular brands