manualshive.com logo in svg

Brocade Communications Systems DCX 8510-8, Hardware Reference Manual

Share
Download
Brocade Communications Systems DCX 8510-8 Hardware Reference Manual Download Page 121

password: xxxxxxxx

switch:admin>

2. Enter the 

slotShow -m 

command and verify that all the installed cards are detected and that their

status is operational (enabled).

switch:admin> slotShow -m

Slot   Blade Type     ID    Model Name     Status

--------------------------------------------------

  1     SW BLADE     97     FC16-32        ENABLED

  2     SW BLADE     77     FC8-64         ENABLED

  3     SW BLADE     97     FC16-32        ENABLED

  4     SW BLADE     97     FC16-32        ENABLED

  5     CORE BLADE   99     CR16-4         ENABLED

  6     CP BLADE     50     CP8            ENABLED

  7     CP BLADE     50     CP8            ENABLED

  8     CORE BLADE   99     CR16-4         ENABLED

  9     SW BLADE     96     FC16-48        ENABLED

 10     SW BLADE     77     FC8-64         ENABLED

 11     SW BLADE     96     FC16-48        ENABLED

 12     SW BLADE     77     FC8-64         ENABLED

switch:admin>

        

3. Verify that the Brocade DCX 8510-8 is functioning correctly by entering 

switchShow

 or

switchStatusShow

.

This 

switchShow

 command displays the Brocade DCX 8510-8 and port status information.

switch:FID128:admin> switchshow

switchName: DCX8510_8

switchType: 120.1

switchState: Online

switchMode: Native

switchRole: Subordinate

switchDomain: 80

switchId: fffc50

switchWwn: 10:00:00:05:1e:39:e4:5a

zoning: ON (ZONE_CONFIG_NAME)

switchBeacon: OFF

FC Router: OFF

Allow XISL Use: OFF

LS Attributes: [FID: 128, Base Switch: No, Default Switch: Yes, Address Mode 0]

Index Slot Port Address Media Speed  State     Proto

=======================================================

0      1    0    500000  --     4G  No_Module     FC

1      1    1    500100  --     4G  No_Module     FC

2      1    2    500200  --     4G  No_Module     FC

3      1    3    500300  --     4G  No_Module     FC

4      1    4    500400  --     4G  No_Module     FC

(output truncated)

4. Verify that all the IP address information is correct by entering 

ipAddrShow 

and checking the results

against the IP information recorded in the config-miscinfo.txt file.

switch:admin> ipaddrshow

SWITCH

Ethernet IP Address: xxx.xxx.xxx.12

Ethernet Subnetmask: 255.55.0.0

Fibre Channel IP Address: 1.2.3.4

Fibre Channel Subnetmask: 255.255.255.0

CP0

Ethernet IP Address: xxx.xxx.xxx.10

Ethernet Subnetmask: 255.55.0.0

HostName : cp0

Gateway Address: xxx.xxx.xxx.1

CP1

Ethernet IP Address: xxx.xxx.xxx.11

Ethernet Subnetmask: 255.55.0.0

HostName : cp1

Gateway Address: .1

Backplane IP address of CP0 : 10.0.0.4

Backplane IP address of CP1 : 10.0.0.5

switch:admin>switch:admin>

Removal and Replacement Procedures

Brocade DCX 8510-8 Backbone Hardware Reference Manual

121

53-1002180-08

Summary of Contents for DCX 8510-8

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands