Brocade Communications Systems DCX 8510-8 Hardware Reference Manual Download Page 118 | Manualshive

Page: 118 / 176

background image

Stopping blade 1

Shutting down the blade....

Stopping blade 2

Shutting down the blade....

Stopping blade 8

Shutting down the blade....

Broadcast message from root (pts/1) Tue Jul 18 14:23:06 2008...

The system is going down for system halt NOW !!

DANGER
Disconnect the power cord from all power sources to completely remove power from the
device.

2. Power off the chassis by flipping all AC power switches to the off position. (The power supply status

LED should turn off.)

3. Remove the power cords from the power supplies and the power outlets.
4. Remove the chassis door.
5. Label the cables connected to all blades and record the connections.
6. Disconnect the cables from the SFP+ transceivers in the application and port blades and set them

aside. If you have mSFP transceivers in FC8-64 port blades, or QSFP transceivers in FC16-64 port
blades, remove the transceivers and cables together and set them aside. The SFP+ transceivers
can be left in the port blades or removed.

7. Disconnect all cables from the control processor and core switch blades.
8. Disconnect any ICL or QSFP cables.

Removing components from the chassis

Follow electrostatic discharge (ESD) precautions. Wear a wrist grounding strap connected to chassis
ground (if the Brocade DCX 8510-8is plugged in) or a bench ground.

DANGER
For safety reasons, the ESD wrist strap should contain a series 1 megaohm resistor.

1. Remove the chassis door (

Chassis door removal and replacement

on page 76) if not already done.

2. Remove the cable management comb (

Cable management comb removal and replacement

on

page 77).

3. Remove the port blades or filler panels (

Port, application, and encryption blade removal and

Blade filler panel removal and replacement

4. Remove the core switch blades (CR16-8) (

Core switch blade (CR16-8) removal and replacement

page 92).

5. Remove the control processor blades (CP8) (

Control processor blade (CP8) removal and

6. Remove the power supplies or filler panels (

Power supply removal and replacement

7. Remove the blower assemblies (

Blower assembly removal and replacement

on page 98).

8. Remove the WWN bezel (logo plate) and WWN cards (

WWN card removal and replacement

page 99).

Installing the replacement chassis

Complete the following steps to install the replacement chassis.

Removing components from the chassis

118

Brocade DCX 8510-8 Backbone Hardware Reference Manual

53-1002180-08

«
...
116
117
118
119
120
...
»

Summary of Contents for DCX 8510-8

















































































































































































Reviews:

No comments

Related manuals for DCX 8510-8

Brand: i3 International Pages: 2

HS21 XM BLADECENTER - L5408 FOR SPEC CPU2006

Brand: IBM Pages: 1

Brand: NEC Pages: 128

ApplianceStor 15MT

Brand: Rasilient Pages: 30

Silex Pricom SX-2000U2

Brand: Silex technology Pages: 1

Brand: Premio Pages: 2

Brand: TYAN Pages: 136

Enterprise Server 33

Brand: Blackberry Pages: 207

4-Port USB 2.0 Device Server over IP...

Brand: Quatech Pages: 2

Brand: Emerson Pages: 23

DIXELL XWEB5000 PRO

Brand: Emerson Pages: 20

Brand: Emerson Pages: 18

Avocent ACS 6000

Brand: Emerson Pages: 93

Brand: Emerson Pages: 114

Centellis 2000 Shelf Release 3.0

Brand: Emerson Pages: 194

Brand: Emerson Pages: 222

Brand: Boundless Pages: 33

Brand: NEC Pages: 69

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands