Brocade Communications Systems DCX 8510-8 Hardware Reference Manual Download Page 53

Page: 53 / 176

Time Alive: 14 days

Time Awake: 0 days

CP BLADE Slot: 6

Header Version: 2

Power Consume Factor: -40

Factory Part Num: 60-1000376-08

Factory Serial Num: AHJ0449E042

Manufacture: Day: 14 Month: 12 Year: 2009

Update: Day: 28 Month: 3 Year: 2011

Time Alive: 299 days

Time Awake: 0 days

CP BLADE Slot: 7

Header Version: 2

Power Consume Factor: -40

Factory Part Num: 60-1000376-08

Factory Serial Num: AHJ0448E0AK

Manufacture: Day: 15 Month: 12 Year: 2009

Update: Day: 28 Month: 3 Year: 2011

Time Alive: 312 days

Time Awake: 0 days

CORE BLADE Slot: 5

Header Version: 2

Power Consume Factor: -240

Power Usage (Watts): -154

Factory Part Num: 60-1002140-02

Factory Serial Num: BPZ0349F00G

Manufacture: Day: 7 Month: 12 Year: 2010

Update: Day: 28 Month: 3 Year: 2011

Time Alive: 49 days

Time Awake: 0 days

CORE BLADE Slot: 8

Header Version: 2

Power Consume Factor: -240

Power Usage (Watts): -148

Factory Part Num: 60-1002140-02

Factory Serial Num: BPZ0349F006

Manufacture: Day: 7 Month: 12 Year: 2010

Update: Day: 28 Month: 3 Year: 2011

Time Alive: 46 days

Time Awake: 0 days

SW BLADE Slot: 11

Header Version: 2

Power Consume Factor: -160

Power Usage (Watts): -115

Factory Part Num: 60-1002144-02

Factory Serial Num: BQB0345F00T

Manufacture: Day: 11 Month: 11 Year: 2010

Update: Day: 28 Month: 3 Year: 2011

Time Alive: 30 days

Time Awake: 0 days

SW BLADE Slot: 12

Header Version: 2

Power Consume Factor: -160

Power Usage (Watts): -79

Factory Part Num: 60-1002144-02

Factory Serial Num: BQB0345F012

Manufacture: Day: 20 Month: 11 Year: 2010

Update: Day: 28 Month: 3 Year: 2011

Time Alive: 3 days

Time Awake: 0 days

POWER SUPPLY Unit: 1

Header Version: 2

Power Consume Factor: 2000

Factory Part Num: 23-0000067-01

Factory Serial Num: AGC2M44EKPH

Manufacture: Day: 29 Month: 12 Year: 2009

Update: Day: 28 Month: 3 Year: 2011

Time Alive: 319 days

Time Awake: 0 days

POWER SUPPLY Unit: 3

Header Version: 2

Power Consume Factor: 2000

Factory Part Num: 23-0000067-01

Factory Serial Num: AGC2M44EKPL

Manufacture: Day: 29 Month: 12 Year: 2009

Update: Day: 28 Month: 3 Year: 2011

Time Alive: 319 days

Time Awake: 0 days

Monitoring System Components

Brocade DCX 8510-8 Backbone Hardware Reference Manual

53-1002180-08

Summary of Contents for DCX 8510-8

















































































































































































Search results

Summary of Contents for DCX 8510-8

Reviews:

Related manuals for DCX 8510-8

Brands by name

Popular brands

Brocade Communications Systems DCX 8510-8, Hardware Reference Manual

Search results

Summary of Contents for DCX 8510-8

Reviews:

Related manuals for DCX 8510-8

Brands by name

Popular brands