Brocade Communications Systems DCX 8510-8 Hardware Reference Manual Download Page 48

Page: 48 / 176

Powering off the Brocade DCX 8510-8

Perform the following steps to power off the Brocade DCX 8510-8.

1. Shut down the Brocade DCX 8510-8 using the

sysShutdown

command.

switch::admin> sysshutdown

This command will shutdown the operating systems on your switch.

You are required to power-cycle the switch in order to restore operation.

Are you sure you want to shutdown the switch [y/n]?y

HA is disabled

Stopping blade 1

Shutting down the blade....

Stopping blade 2

Shutting down the blade....

Stopping blade 8

Shutting down the blade....

Broadcast message from root (pts/1) Tue Aug 23 14:23:06 2010...

The system is going down for system halt NOW !!

2. Power off the chassis by flipping the AC power switches on the power supplies to O (LEDs inside

AC power switches should turn off). To maintain the ground connections, leave power cords
connected to the power supplies and to the electrical outlets.

Powering off the Brocade DCX 8510-8

Brocade DCX 8510-8 Backbone Hardware Reference Manual

53-1002180-08

Summary of Contents for DCX 8510-8

















































































































































































Search results

Summary of Contents for DCX 8510-8

Reviews:

Related manuals for DCX 8510-8

Brands by name

Popular brands

Brocade Communications Systems DCX 8510-8, Hardware Reference Manual

Search results

Summary of Contents for DCX 8510-8

Reviews:

Related manuals for DCX 8510-8

Brands by name

Popular brands