manualshive.com logo in svg

Brocade Communications Systems DCX 8510-8, Hardware Reference Manual

Share
Download
Brocade Communications Systems DCX 8510-8 Hardware Reference Manual Download Page 85

• The 

haShow

 command indicates an error.

• The clock is inaccurate, or the CP blade does not boot up or shut down normally.
• Any of the following messages display in the error log:

‐

"Slot unknown" message relating to a CP slot

‐

CP blade errors or I2C timeouts

‐

FRU: FRU_FAULTY messages for a CP blade

‐

Configuration loader messages or "Sys PCI config" messages

‐

Generic system driver messages ("FABSYS")

‐

Platform system driver messages ("Platform")

‐

EM messages that indicate a problem with a CP blade

‐

Function fail messages for the CP master

For more information about error messages, refer to the 

Fabric OS Message Reference

.

Recording critical Brocade DCX 8510-8 information

Back up the backbone configuration before you replace a CP blade. Refer to the 

Fabric OS

Administrator's Guide

 for backup information.

NOTE

The following instructions reference specific slot numbers. These numbers will be different between the
DCX 8510-8/DCX and the DCX 8510-4/DCX-4S chassis.

1. Connect to the chassis and log in as 

admin

, using a serial console connection.

2. Enter 

haShow

 to determine which CP blade is active. The following example is from a DCX chassis.

DCX_124:admin> haShow

Local CP (Slot 7, CP1) : Active

Remote CP (Slot 6, CP0) : Standby, Healthy

HA Enabled, Heartbeat Up, HA State Synchronized

3. Enter all remaining commands from the serial console for the active CP blade, unless otherwise

indicated. For more information about commands, refer to the 

Fabric OS Command Reference

.

4. If the active CP blade is faulted, automatic fail over to the standby CP blade should have occurred.

Confirm that the standby CP blade is active and power off the faulted CP blade, log in to the standby
CP blade, and skip to step 7.

If automatic failover has not occurred, manually failover the faulty blade by moving the slider to the
off position (down in the DCX 8510-8). Then power off the faulted blade, log in to the standby CP
blade, and skip to step 7.

5. If both CP blades are healthy and you want to replace the standby CP blade, log in to the active CP

blade and skip to step 7.

6. If both CP blades are healthy and you want to replace the active CP blade, log in to the active CP

blade and run the following steps:
a)

Run the 

haFailover

 command to make the standby CP blade the active blade. The currently

active CP blade becomes the standby blade. Wait until the status LED on the currently
active CP blade is no longer lit.

b)

Confirm the completion of the failover by running the 

haShow

 command.

c)

Log in to the new active CP blade.

7. Run 

firmwareShow

 to note the firmware version of the active CP blade.

Recording critical Brocade DCX 8510-8 information

Brocade DCX 8510-8 Backbone Hardware Reference Manual

85

53-1002180-08

Summary of Contents for DCX 8510-8

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands