manualshive.com logo in svg

Brocade Communications Systems DCX 8510-8, Hardware Reference Manual

Share
Download
Brocade Communications Systems DCX 8510-8 Hardware Reference Manual Download Page 130

Limitations of FCOE10-24 blade

The following limitations have to be considered when using FCOE10-24 application blade with Fabric
OS 7.3.0, on the DCX 8510-8 chassis:

• FCOE10-24 blade is supported only in slot 1 of the 8510-8 chassis.
• Supports maximum of one FCOE10-24 blade per 8510-8 chassis.
• FCOE10-24 blade can be installed concurrently with FC16-32 and FC8-32E blades only.
• FCOE10-24 blade cannot be used in the DCX 8510-8 chassis with FC16-48, FC16-48E, FC8-64 or

FC16-64 blades.

• FCOE10-24 blade cannot be used in a DCX 8510-8 chassis with other intelligent or application

blades.

• Support is limited to FCoE direct attach only.
• Upgrade and downgrade considerations are same as DCX.

NOTE

For complete list of limitations on the FCOE10-24 blade, refer to the Fabric OS Release Notes.

Limitations of FCOE10-24 blade

130

Brocade DCX 8510-8 Backbone Hardware Reference Manual

53-1002180-08

Summary of Contents for DCX 8510-8

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands