background image

Belarus 1025/1025.2/1025.3

 

Section G. Scheduled maintenance

 

G 51

 

Seasonal maintenance.

 

Combine seasonal maintenance with regular maintenance operations 

Substance of works 

During transition to autumn-winter season (with 
settled average daily temperature  below + 5° 

С

During transition to spring-summer season (with 
settled average daily temperature above + 5 °

С

Change summer oil grades for winter grades  (see 

lubrication table): 

Change winter oil grades for summer grades 

In diesel casing 

In diesel casing 

In the case of hydraulic assemblies and HS 

In the case of hydraulic assemblies and HS. 

In the transmission case 

In the transmission case 

In FDA case and wheel reduction gears 

In FDA case and wheel reduction gears 

In case (left-, right-hand ) of “wet” brakes 

In case (left-, right-hand) of “wet” brakes 

Fill diesel cooling system with antifreeze fluid, having 

in advance washed the cooling system 

 

Clean calibrated opening of connecting pipe bolt 

of the electric torch heater; diesels with ETH. 

 

Summary of Contents for 1025 2008














































































































































































































Reviews: