manualshive.com logo in svg

Belarus 1025 2008, Operation Manual

Share
Download
Belarus 1025 2008 Operation Manual Download Page 167

Belarus 1025/1025.2/1025.3

 

Section H. Adjustments

 

H17

 

 

Checking and adjusting two-

wire braking valve of the 

pneumatic system and drive 

thereof

 

Make all adjustments with tractor brake 

controls in free position.

 

1. Connect pressure gauge with scale at 

least  10  kgf/cm

2

  to drive connecting 

head (with yellow cover) of the tractor 

pneumatic drive

 

Switch on compressor and fill cylinder 

with air up to pressure  7.7...8.0 

kgf/cm

2

  by pressure gauge on the 

instruments panel

 

Air pressure by pressure gauge 

connected to control head (with yellow 

cover), with fully pressed interlocked 

wheel brakes, or fully engaged parking 

brake, should be at least 7.7 kgf/cm

2

.If 

it is less then the above-given value, 

perform the following operations:

 

Check if there is clearance of 1…2 mm 

between pin (3) and upper grooves’ 

edges in levers. If there is no 

clearance, pull out pin(3) and adjust 

length of tie-rod using tip (2).

 

Check and, if necessary, adjust loading 

of spring (4) to dimension 37 mm by 

turning nuts (1), and secure them with 

cotter pin.

 

If air pressure by pressure gauge 

connected to the head didn’t reach 

required value, perform the following 

operations:

 

Disconnect tie-rod from eyelet (7)  and 

remove rubber sheath (5)  from brake 

valve to get access to nut (6).

 

Unscrew eyelet (1) by 2...3 turns , and 

by unscrewing nut (6) set air pressure 

to value at least 7.7.

 

 

 

9.  Screw in eyelet  (7) to the end inside 

nut (6), and secure eyelet with cotter pin.

 

10.  Put on sheath (5) and connect tie-rod 

to eyelet (7).

 

IMPORTANT! 

When brake valve and its 

drive are correctly adjusted, air 

pressure in the connecting control 

head (with yellow cover) should equal 

zero, with interlocked wheel brakes’ 

pedals not pressed, and parking brake 

fully disengaged. 

 

2.

 

3.

 

4.

 

5.

 

6.

 

7.

 

8.

 

Summary of Contents for 1025 2008














































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands