Baldor VS1GV21-1B, Installation & Operating Manual, Page: 150 / 204

12-4 Monitor and RTC Description MN765
P# Type Name Unit Help
105 COMPOSITE REF %
Composite Reference. - Reference generated composite reference
parameter block.
106 POS MOVE STATUS
Position Move Status. - 15 Preset Position Mode status. 0x0=inactive,
0x1-0xF=active, 0x101-0x10F=complete
107 R/W RTC EDGE COUNTER
RTC Edge Counter. - General purpose date/time edge counter used in
Real Time Clock Features.
108 R/W RTC OUTPUTS
RTC Virtual Outputs. - Outputs set by the RTC and mapped to real
outputs if enabled.
109 R/W RTC MSG STATUS
RTC Message Status. - Individual bits are mapped to RTC message
when set
110 LAST POWERDOWN
Last Drive Power Down Date. - The date and time the drive was last
turned off.
111 COMPONENT A %
Component A of Composite Reference. - First part of the composite
reference signal.
112 COMPONENT B %
Component B of Composite Reference. - First part of the composite
reference signal.
113 R/W PLC TIMER A
PLC Mode Timer A Counter. - General purpose timer/counter in 10ms
clock ticks.
114 R/W PLC TIMER B
PLC Mode Timer B Counter. - General purpose timer/counter in 10ms
clock ticks.
115 ENC POS FB SPEED % Speed reference set by Pulse Follower EXB.
116 MACRO STATUS
ID number of last executed macro (none if no macros have been
executed).
117 R/W PLC Timer C
PLC Mode Timer C Counter- General purpose timer/counter in 10ms
clock ticks.
118 R/W PLC Timer D
PLC Mode Timer D Counter - General purpose timer/counter in 10ms
clock ticks.
201 LOC SPEED REF Hz
Local Speed Reference. - Local speed reference from keypad.
Reference can be entered in Hz or RPM
202 E-POT SPEED REF Hz E-Pot Speed Ref. - Electronic pot speed reference
301 FAULT LOG TIME Fault Log Time. Time stamp for fault log entries
302 FAULT LOG MSG Fault Log Message.
501 COUNTS CNT Counts. Accumulated position in encoder pulses per revolution
502 REVOLUTIONS REV
Revolutions. Accumulated revolutions since power up. Encoder PPR
parameter sets the revolution count
503 OPT1 ANA IN1 V/mA Option 1 Analog Input 1. Option board 1 analog input 1
504 OPT1 ANA IN2 V/mA Option 1 Analog Input 2. Option board 1 analog input 2
505 OPT2 ANA IN1 V/mA Option 2 Analog Input 1. Option board 2 analog input 1
506 OPT2 ANA IN2 V/mA Option 2 Analog Input 2. Option board 2 analog input 2
507 OPT1 ANA OUT1 V/mA Option 1 Analog Output 1. Option board 1 analog output 1
508 OPT1 ANA OUT2 V/mA Option Board 1 Analog Output 2. Option 1 analog output 2
509 OPT2 ANA OUT1 V/mA Option 2 Analog Output 1. Option board 2 analog output 1
510 OPT2 ANA OUT2 V/mA Option 2 Analog Output 2. Option board 2 analog output 2
511 TX CNTS CNT
PF Tx Counts. PF transmitted accumulated position in encoder pulses
per revolution
512 TX REVS REVS
PF Tx Revolutions. PF transmitted accumulated revolutions since power
up. Encoder PPR parameter sets the revolution count
513 RX CNTS CNT
PF Rx Counts. PF received accumulated position in encoder pulses per
revolution
Table 12-1 Monitor Parameters Descriptions Continued