background image

Administering UDP port selection

You can administer the phone from the Avaya Communication Manager Network Region which is
form to support UDP port selection.

For information about Avaya Communication Manager implementation, see 

Administration for

Network Connectivity for Avaya Communication Manager, 555-233-504

 on the 

Avaya Support

website

.

Administer the switch to use a port within the proper range for the specific LAN, and the IP
deskphone(s) copy that port. If no UDP port range is administered on the switch, the IP
deskphone uses an even-numbered port, randomly selected from the interval 4000 to 10000.

Related links

Call server administration

 on page 73

Administering RSVP

The phone support the Resource Reservation Protocol (RSVP) for IPv4 audio connections only.

You can fully enable RSVP by provisioning CM ip-network-region.

Related links

Call server administration

 on page 73

Administering QoS

The IP deskphones support both IEEE 802.1D/Q and DiffServ.

Related links

Call server administration

 on page 73

Administering IEEE 802.1Q

The phone can simultaneously support receipt of packets that are tagged, or not tagged according
to the IEEE 802.1Q standard. To support IEEE 802.1Q, you can administer phone from the
network through LLDP, or by appropriate administration of the DHCP or HTTP/HTTPS servers.

You can administer the IEEE 802.IQ QoS parameters L2QAUD, and L2QSIG through the IP
Network Region form. To set these parameters at the switch, see sections on 

Quality of Service

(QoS)

 and 

Voice quality administration

 in 

Administration for Network Connectivity for Avaya

Communication Manager

, 555-233-504.

Related links

Call server administration

 on page 73

Administering DIFFSERV

The DiffServ values change to the values administered on the call server as soon as the phone
registers. Administer the DSCPAUD and DSCPSIG parameters to configure Diffserv for the
deskphone. Unless there is a specific need in your enterprise LAN, do not change the default
values.

Administering your phone

May 2018

Installing and Administering Avaya J169/J179 IP Phone H.323

74

Comments on this document? [email protected]

Summary of Contents for J169












































































































































































































Reviews: