Avaya J169 Installing And Administering Download | Manualshive

Page: 142 / 203

background image

These phones:

• do not support LLDP on the secondary Ethernet interface.

• do not forward frames received with the 802.1AB LLDP group multicast address as the

destination MAC address between the Ethernet line interface and the secondary Ethernet
interface.

The phone initiates LLDP after receiving an LLDPDU message from an appropriate system. After
the phone is initiated, the phone sends an LLDPDU every 30 seconds or as specified by
LLDP_XMIT_SECS parameter with the following contents:

Table 10: LLDPDU transmitted by the phones

Category

TLV Name (Type)

TLV Info String (Value)

Basic Mandatory

Chassis ID

IPv4 IP Address of phone.

Basic Mandatory

Port ID

MAC address of the phone.

Basic Mandatory

Time-To-Live

120 seconds.

Basic Optional

System Name

The Host Name sent to the DHCP server in DHCP
option 12.

Basic Optional

System Capabilities

Bit 2 (Bridge) is set in the System Capabilities if the
phone has an internal Ethernet switch. If Bit 2 is set
in Enabled Capabilities then the secondary port is
enabled.

Bit 5 (phone) in the System Capabilities. If Bit 5 is set
in the Enabled Capabilities than the phone is
registered.

Basic Optional

Management Address

Mgmt IPv4 IP Address of phone.

Interface number subtype = 3 (system port). Interface
number = 1.

OID = SNMP MIB-II sysObjectID of the phone.

IEEE 802.3
Organization Specific

MAC / PHY
Configuration / Status

Reports auto-negotiation status and speed of the
uplink port on the phone.

TIA LLDP MED

LLDP-MED Capabilities

Media Endpoint Discovery - Class III - IP Telephone.

TIA LLDP MED

Extended

Power-Via-MDI

Power Value = 0 if the phone is not currently
powered through PoE, else the maximum power
usage of the deskphone plus all modules and
adjuncts powered by the phone in tenths of a watt.

TIA LLDP MED

Network Policy

Tagging Yes/No, VLAN ID for voice, L2 Priority,
DSCP Value.

TIA LLDP MED

Inventory – Hardware
Revision

MODEL - Full Model Name.

TIA LLDP MED

Inventory – Serial
Number

Phone serial number.

Table continues…

Administering your phone

May 2018

Installing and Administering Avaya J169/J179 IP Phone H.323

142

Comments on this document? [email protected]

«
...
140
141
142
143
144
...
»

Summary of Contents for J169












































































































































































































Reviews:

No comments

Related manuals for J169

EBX70 - CELL PHONE

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 46

Brand: Panasonic Pages: 38

Brand: Panasonic Pages: 45

Galaxy XCover FieldPro

Brand: Samsung Pages: 14

Brand: Samsung Pages: 55

Galaxy Z Flip 5G

Brand: Samsung Pages: 2

Brand: Samsung Pages: 184

Brand: Samsung Pages: 2

Brand: Samsung Pages: 9

Brand: Samsung Pages: 25

Brand: Samsung Pages: 16

Brand: Fairphone Pages: 22

blackview Crown

Brand: Iget Pages: 76

Brand: Collage Investments Pages: 34

Brand: Snapfon Pages: 9

Brand: T-Mobile Pages: 258

Brand: Blu Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands