Avaya J169 Installing And Administering Download | Manualshive

Page: 76 / 203

background image

SET MSGNUM

1234

where

1234

is the Voice Mail extension for the CM hunt group or VDN.

Note:

You can use MSGNUM only when you aliase the deskphone using non-native support. You
must configure messaging for native support. A separate Voice Mail extension can be
administered for each station.

Related links

Communication Manager Administration

Call transfer administration

This section provides information about call transfer behaviors to consider when you administer
the call server. The phone application presents a user interface, based in part on the deduction of
the call state. The following server-based features can interact with the user interface resulting in a
call state that might need explanation:

• The system parameter Abort Transfer? is set to

Yes

. After you start a transfer, you cannot

press a non-idle call appearance until the transfer is complete or the transfer is aborted.

• The system parameter Abort Transfer? is set to

No

: The transfer proceeds normally even if

the user presses a non-idle call appearance before the transfer is complete.

• The system parameter Transfer Upon Hang-up is set to

No

: The user must press the

Complete

softkey after dialing the intended destination for the transfer to be completed.

• The system parameter Transfer Upon Hang-up is set to

Yes

: The user can hang up

immediately after dialing and the transfer proceeds normally.

The features Abort Transfer and Transfer Upon Hang-up can interact. If a user initiates a transfer,
dials the destination, and hangs up without pressing the

Complete

softkey, the three possible

outcomes are:

• The transfer is completed. Transfer Upon Hang-up is set to

Yes

, regardless of the Abort

Transfer? setting.

• The transfer is aborted. Transfer Upon Hang-up is set to

No

and Abort Transfer? is set to

Yes

.

• The transfer is denied. Transfer Upon Hang-up is set to

No

and Abort Transfer? is set to

No

and the call appearance of the transferee remains on soft hold.

Attempts to transfer an outside call to an outside line are denied. However, the user can drop the
denied destination and initiate a transfer to an internal destination.

You can use the

Toggle Swap

feature to swap the soft-held and setup call appearances. That is,

the setup call appearance becomes soft-held, and the soft-held call appearance becomes active
as the setup call appearance. This feature works only once the setup call appearance is
connected on a call. If

Toggle Swap

is pressed while the setup call appearance has ringback, the

call server sends a broken flutter to the setup call appearance. If you press

Toggle Swap

while the

Administering your phone

May 2018

Installing and Administering Avaya J169/J179 IP Phone H.323

76

Comments on this document? [email protected]

«
...
74
75
76
77
78
...
»

Summary of Contents for J169












































































































































































































Reviews:

No comments

Related manuals for J169

Brand: Samsung Pages: 212

Brand: Unihertz Pages: 97

Brand: Uniden Pages: 24

Brand: Fisher-Rosemount Pages: 116

Brand: GS-hosted Pages: 26

Brand: B Mobile HK Pages: 43

Brand: Samung Pages: 150

Brand: H3C Pages: 12

Brand: Blaupunkt Pages: 38

Brand: Polycom Pages: 2

Brand: NGM Pages: 166

Brand: CHI MEI Pages: 26

Brand: SENDO Pages: 54

Brand: Pantech Pages: 55

Brand: i.safe MOBILE Pages: 132

Instinct HD SPH-M850

Brand: Samsung Pages: 242

Intercept SPH-M910

Brand: Samsung Pages: 233

VERIZON SCHU460

Brand: Samsung Pages: 193

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands