Avaya J169 Page 143 Installing And Administering Download

Page: 143 / 203

Category

TLV Name (Type)

TLV Info String (Value)

TIA LLDP MED

Inventory – Manufacturer
Name

Avaya.

TIA LLDP MED

Inventory – Model Name

MODEL with the final D

xxx

characters removed.

Avaya Proprietary

PoE Conservation Level
Support

Provides power conservation abilities and settings,
Typical and Maximum Power values.

OUI = 00-40-0D (hex), Subtype = 1.

Avaya Proprietary

Call Server IP Address

Call Server IP address.

Subtype = 3.

Avaya Proprietary

IP Phone Addresses

Phone IP address, Phone address mask, Gateway IP
address.

Subtype = 4.

Avaya Proprietary

File Server

File Server IP address.

Subtype = 6.

Avaya Proprietary

802.1Q Framing

802.1Q Framing = 1 if tagging or 2 if not.

Subtype = 7.

Basic Mandatory

End-of-LLDPDU

Not applicable.

On receipt of a LLDPDU message, the phones will act on the TLV elements described in the
following table:

Table 11: Impact of TLVs Received by System Parameter Values

System Parameter
Name

TLV Name

Impact

PHY2VLAN

IEEE 802.1 Port
VLAN ID

The value is changed to the Port VLAN identifier in the
TLV.

L2QVLAN and L2Q

IEEE 802.1 VLAN
Name

The value is changed to the TLV VLAN Identifier. L2Q will
be set to 1 (ON). VLAN Name TLV is only effective if the
following conditions are met:

• The phone is not registered with the call server.

• Name begins with VOICE (letters are not case-

sensitive).

• The VLAN is not zero.

• DHCP Client is activated.

• The phone is registered but is not tagging layer 2 frames

with a non-zero VLAN ID.

If VLAN Name causes the phone to change VLAN and the
phone already has an IP Address the phone will release
the IP Address and reset.

Table continues…

Administering Deskphone Options

May 2018

Installing and Administering Avaya J169/J179 IP Phone H.323

143

Comments on this document? [email protected]

Summary of Contents for J169












































































































































































































Search results

Summary of Contents for J169

Reviews:

Related manuals for J169

Brands by name

Popular brands

Avaya J169, Installing And Administering

Search results

Summary of Contents for J169

Reviews:

Related manuals for J169

Brands by name

Popular brands