Avaya J169 Installing And Administering Download

Page: 68 / 203

Destination Port

Source Port

Use

UDP or TCP?

A port number specified in the SLA

test request message

50012

Transmitted SLA RTP test

packets

UDP

33434 – 33523,starts with 33434,

increments by 1 for each message

sent, 3 messages for each hop, up

to 30 hops

50013

Transmitted SLA traceroute

messages

UDP

As specified by CM, or as

specified in a CNA RTP test

request

As specified by

CM or as

reserved for CNA

RTP tests

Transmitted RTP and SRTP

packets

UDP

The next higher port number if the

port used for RTP is even, or the

next lower port number if the port

used for RTP is odd

The next higher

port number if the
port used for RTP

is even, or the

next lower port

number if the port

used for RTP is

odd

RTCP and SRTCP packets
transmitted to the far end of
the audio connection

UDP

RTCPMONPORT

The next higher

port number if the
port used for RTP

is even, or the

next lower port

number if the port

used for RTP is

odd

RTCP packets transmitted to
an RTCP monitor

UDP

1719

An unused port

number in the

range from 49300

to 49309

H.323 RAS messages

UDP

A port number specified in the SLA

discovery message

Any unused port

number

Transmitted SLA registration
messages

TCP

Determined by SNMP mgmt app

161

Transmitted SNMP messages

UDP

Determined by the SSH client or

the client Operating system

Transmitted SSH messages

TCP

Security

For information about toll fraud, see the respective call server documents on the

Avaya Support

website

. The phone cannot guarantee resistance to all Denial of Service (DoS) attacks. However,

checks and protections are in-built to resist such attacks while maintaining appropriate service to
legitimate users.

All IP phones that have WML Web applications support Transport Layer Security (TLS). The
deskphone uses TLS to establish a secure connection to a HTTPS server, in which the upgrade

Administering your phone

May 2018

Installing and Administering Avaya J169/J179 IP Phone H.323

Comments on this document? [email protected]

Summary of Contents for J169












































































































































































































Search results

Summary of Contents for J169

Reviews:

Related manuals for J169

Brands by name

Popular brands

Avaya J169, Installing And Administering

Search results

Summary of Contents for J169

Reviews:

Related manuals for J169

Brands by name

Popular brands