Avaya J169 Page 173 Installing And Administering Download

Page: 173 / 203

You must specify WMLIDLEURI only for phones installed in public areas through the use of a
GROUP parameter.

Table 18: Idle Timer Settings and Results

Shortest Timer

Middle Timer

Longest Timer

Operation

WMLIDLETIME and
WMLIDLEURI are
null

BAKLIGHTOFF is
non-zero

SCREENSAVERON
is non-zero

Default operation:

After BAKLIGHTOFF minutes, the
backlight is set to low power mode.

After (SCREENSAVERON –
BAKLIGHTOFF) additional minutes,
the screen saver is displayed.

WMLIDLETIME has no effect.

WMLIDLETIME and
WMLIDLEURI are
null

SCREENSAVERON
is non-zero

BAKLIGHTOFF is
non-zero

After SCREENSAVERON minutes,
the phone displays the screen saver.

After (BAKLIGHTOFF-
SCREENSAVERON) additional
minutes, the backlight is set to low
power mode.

WMLIDLETIME and
WMLIDLEURI are
non-null

BAKLIGHTOFF is
non-zero

SCREENSAVERON
is non-zero

Every WMLIDLETIME minutes, a
GET is sent for WMLIDLEURI, and
the the phone displays a browser.
The Web page may contain a timer
to cycle through additional Web
pages.

The backlight is set to low power
mode after the specified time and
the phone displays a screen saver
on the SCREENSAVERON value.

Note:

You can administer the Backlight Off icon on a IP deskphone softkey.

The behavior of backlight for any adjunct button module depends on the backlight of the
phone to which you attach the button module.

Administering Applications and Options

May 2018

Installing and Administering Avaya J169/J179 IP Phone H.323

173

Comments on this document? [email protected]

Summary of Contents for J169












































































































































































































Search results

Summary of Contents for J169

Reviews:

Related manuals for J169

Brands by name

Popular brands

Avaya J169, Installing And Administering

Search results

Summary of Contents for J169

Reviews:

Related manuals for J169

Brands by name

Popular brands