Avaya J169 Installing And Administering Download

Page: 187 / 203

Correcting a power interruption

If power to a IP deskphone is interrupted while the phone is saving the application file, the HTTP/

HTTPS application can stop responding. If this occurs, restart the phone.

Using the VIEW procedure for troubleshooting

About this task

Use the following procedure to verify the current values of system parameters and file versions.

Note:

You can use the ADDR option to view IP addresses if needed. The IP addresses might have

been entered incorrectly. Verify whether you were provided with correct IP addresses.

Procedure

1. Select

VIEW

from the Screen.

The phone displays the following options:

IP Parameters

Quality of Service

, and

Miscellaneous

2. Tap the category that you want to see.

The information for that category is displayed.

3. Press

Back

at any time to return to the screen.

Installation error and status messages

The phone displays messages in the currently selected language or in the language specified by

the LANGSYS parameter value, if the phone is logged off. If English is not the selected language,

the phone displays messages in English only when the message are associated with local

procedures, for example, MUTE VIEW.

The phone displays most of the messages for only about 30 seconds, and then the phone is reset.

The most common exception is

Extension in Use

, display more than 30 seconds and which

remains until you perform any further action on the phone.

Note:

For VPN-related error and status messages, see the

VPN Setup Guide for 9600 Series IP

Telephones, 16-602968

Correcting a power interruption

May 2018

Installing and Administering Avaya J169/J179 IP Phone H.323

187

Comments on this document? [email protected]

Summary of Contents for J169












































































































































































































Search results

Summary of Contents for J169

Reviews:

Related manuals for J169

Brands by name

Popular brands

Avaya J169, Installing And Administering

Search results

Summary of Contents for J169

Reviews:

Related manuals for J169

Brands by name

Popular brands