Avaya J169 Installing And Administering Download

Page: 58 / 203

Parameter

Value

Description

files from HTTPS that has a
certificate signed by CA. The
root certificate of this CA
must be in the trusted
certificate repository.

OPSTAT

101

Restricts displaying the
configuration information on the
deskphone.

SNMPSTRING

NULL

Avaya J169/J179 IP
Phonesupports SNMPv3

SSH_ALLOWED

Disables SSH.

NVVPNMODE

VPN not supported in the FIPS
mode.

VPNPROC

VPN not supported in the FIPS
mode.

TPSLIST

NULL

Push server does not support
TLS.

VLANSEP

Enables VLAN separation that
restricts the computer connected
to the PC port from connecting to
the phone VLAN.

VLANSEPMODE

Enforces VLAN separation. When
set to 1, VLAN separation is
enforced for both untagged and
tagged packets from the
computer and the network port.
The computer cannot send
tagged or untagged packets to
the deskphone processor.

L2QVLAN

Address of the voice VLAN

The deskphone sends the
untagged data packets to this
VLAN. The value must not be 0 or
the PHY2VLAN address.

L2Q

0: Auto

1: On

0: Auto - The deskphone starts
sending tagged packets to the
voice VLAN. If the VLANTEST
timer has expired, the phone
sends untagged packets.

1: Tagging – The deskphone
starts sending tagged packets on
voice VLAN and if VLANTEST
timer expires, the phone then

Table continues…

Administering your phone

May 2018

Installing and Administering Avaya J169/J179 IP Phone H.323

Comments on this document? [email protected]

Summary of Contents for J169












































































































































































































Search results

Summary of Contents for J169

Reviews:

Related manuals for J169

Brands by name

Popular brands

Avaya J169, Installing And Administering

Search results

Summary of Contents for J169

Reviews:

Related manuals for J169

Brands by name

Popular brands