Avaya J169 Installing And Administering Download | Manualshive

Page: 144 / 203

background image

System Parameter
Name

TLV Name

Impact

If the TLV VLAN ID matches the VLAN ID the phone is
using, the VLAN ID is marked as set by LLDP. Otherwise,
if already registered, the phone waits until there are no
active calls, releases its IP Address, turns on tagging with
the TLV VLAN ID, sets L2Q to

on

changes the default L2Q

to

on

and resets. If there is no valid IP Address, the phone

immediately starts tagging with the new VLAN ID without
resetting.

L2Q, L2QVLAN,
L2QAUD, L2QSIG,

DSCPAUD,
DSCPSIG

MED Network Policy
TLV

L2Q - set to 2 (off) If T (the Tagged Flag) is set to 0; set to
1 (on) if T is set to 1.

L2QVLAN - set to the VLAN ID in the TLV.

L2QAUD and L2QSIG - set to the Layer 2 Priority value in
the TLV.

DSCPAUD and DSCPSIG - set to the DSCP value in the
TLV.

The system checks whether a reset is necessary to obtain
a new IP address due to a change in the values of the
parameters L2Q or L2QVLAN. This TLV is ignored if:

• the value of USE_DHCP is 0 and the value of IPADD is

not

0.0.0.0

, or

• the Application Type is not 1 (Voice), or

• the Unknown Policy Flag (U) is set to 1.

MCIPADD

Proprietary Call
Server TLV

MCIPADD will be set to this value if it has not already
been set.

TLSSRVR and
HTTPSRVR

Proprietary File
Server TLV

TLSSRVR and HTTPSRVR will be set to this value if
neither of them have already been set.

L2Q

Proprietary 802.1 Q
Framing

The default L2Q is set to the value of this TLV. No change
is made to the current L2 tagging, but the new default
value is used on the next reboot.

• If the 802.1Q Framing value is 1, L2Q will be set to “1”

(on)

• If the 802.1Q Framing value is 2, L2Q will be set to “2”

(off)

• If the 802.1Q Framing value is 3, L2Q will be set to “0”

(auto)

Proprietary - PoE
Conservation TLV

This proprietary TLV can initiate a power conservation
mode. The phones that support this will turn the phone
backlight and the backlight of an attached Button Module
on or off in response to this TLV.

Table continues…

Administering your phone

May 2018

Installing and Administering Avaya J169/J179 IP Phone H.323

144

Comments on this document? [email protected]

«
...
142
143
144
145
146
...
»

Summary of Contents for J169












































































































































































































Reviews:

No comments

Related manuals for J169

Brand: Yealink Pages: 8

Brand: T-Mobile Pages: 2

Brand: Panasonic Pages: 100

Brand: Panasonic Pages: 5

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 6

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 129

Brand: Samsung Pages: 98

Brand: FLY Pages: 33

Brand: Plum Pages: 24

Brand: Verykool Pages: 30

Brand: Micromax Pages: 40

Brand: Grandstream Networks Pages: 19

AQUOS ZETA SH-09D

Brand: Docomo Pages: 45

Brand: Pantech Pages: 77

Transform SPH-M920

Brand: Samsung Pages: 238

Brand: Samsung Pages: 203

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands