Avaya J169 Installing And Administering Download

Page: 73 / 203

Call server requirements

Before you perform administrative tasks, ensure that you have installed the proper hardware and

your call server software is compatible with your phone. Use the latest PBX software and IP phone

firmware.

Related links

Communication Manager Administration

on page 72

Call server administration

For call server administration information not covered in this chapter, see the following documents
on the

Avaya Support website

•

Administering Avaya Aura Communication Manager

, 03-300509 for more instructions for

administering an IP phone system on Communication Manager.

For information on the process of adding new phones, see chapter 6,

Managing Telephones

For related screen illustrations and field descriptions, see chapter on

Screen References

•

Administration for Network Connectivity for Avaya Communication Manager

, 555-233-504 for

more information about switch administration for your network.

Related links

Communication Manager Administration

on page 72

Administering the IP interface and addresses

on page 73

Administering UDP port selection

on page 74

Administering RSVP

on page 74

Administering QoS

on page 74

Administering IEEE 802.1Q

on page 74

Administering DIFFSERV

on page 74

Administering NAT

on page 75

Administering the IP interface and addresses

Follow these general guidelines:

• Define the IP interfaces for each CLAN and Media processor circuit pack on the call server

that uses the IP Interfaces screen. For more information, see

Administration for Network

Connectivity for Avaya Communication Manager

, 555-233-504.

• On the Customer Options form, verify that the IP Stations field is set to

(Yes). If it is not set

to (Y), contact your Avaya sales representative. This guideline does not apply to the IP
Softphone.

Related links

Call server administration

on page 73

Communication Manager Administration

May 2018

Installing and Administering Avaya J169/J179 IP Phone H.323

Comments on this document? [email protected]

Summary of Contents for J169












































































































































































































Search results

Summary of Contents for J169

Reviews:

Related manuals for J169

Brands by name

Popular brands

Avaya J169, Installing And Administering

Search results

Summary of Contents for J169

Reviews:

Related manuals for J169

Brands by name

Popular brands