Avaya J129 Installing And Administering Download

Page: 39 / 133

Parameter name

Default value

Description

Value operation:

• 0: Disabled

• 1: Enabled

VLANSEPMODE is configured through the

Settings

file.

PHY2TAGS

Determines whether or not VLAN tags are
stripped on Ethernet frames going out of the
Computer (PC) port.

Value operation:

• 0: Strip tags. VLAN tags are stripped from

Ethernet frames leaving the computer (PC) port
of the phone.

• 1: Does not strip tags. VLAN tags are not

stripped from Ethernet frames leaving the
Computer (PC) port of the phone.

PHY2TAGS is configured through the

Settings

file.

L2QVLAN

Specifies the voice VLAN ID to be used by IP
phones.

Valid values are 0 through 4094.

L2QVLAN is configured through:

• Local admin procedure

• A name equal to value pair in DHCPACK

message

• SET command in the

Settings

file

• DHCP option 43

• LLDP

PHY2VLAN

Specifies the value of the 802.1Q VLAN ID that is
used to identify network traffic going into and
coming out of the internal CPU of the phone.

Valid values are 0 through 4094.

PHY2VLAN is configured through:

• SET command in the

Settings

file

• LLDP

L2QAUD

Specifies the value of the VLAN priority portion of
the VLAN tag when the phone generates tagged
Ethernet frames from the internal CPU of the

Table continues…

Virtual LAN (VLAN) overview

September 2017

Installing and Administering Avaya J129 IP Phone

Comments on this document? [email protected]

Summary of Contents for J129






































































































































Search results

Summary of Contents for J129

Reviews:

Related manuals for J129

Brands by name

Popular brands

Avaya J129, Installing And Administering

Search results

Summary of Contents for J129

Reviews:

Related manuals for J129

Brands by name

Popular brands