Avaya J129 Installing And Administering Download Page 121

Page: 121 / 133

Parameter name

Default value

Description

RTCPMON

Null

Specifies the IP or DNS address for the RTCP
monitor.

You can set this parameter only if the environment
is not an Avaya environment. The values can
range from 0 through 255 characters.

RTCPMONPERIOD

Specifies the interval, in seconds, for sending out
RTCP monitoring reports. Valid values are from 5
to 30 seconds.

RTCPMONPORT

5005

Specifies the RTCP monitor port number.

You can set this parameter only if the environment
is not an Avaya environment. The values can
range from 0 through 65535. Default is 5005.

RTP_PORT_LOW

Specifies the lower limit of the UDP port range to
be used by RTP or RTCP and SRTP or SRTCP
connections.

The values can range from 1024 through 65503.

RTP_PORT_RANGE

Specifies the range or number of UDP ports
available for RTP or RTCP and SRTP or SRTCP
connections

This value is added to RTP_PORT_LOW to
determine the upper limit of the UDP port range.

The values can range from 32 through 64511.

S
SCEPPASSWORD

$SERIALNO

Specifies the password to be included in the
challengePassword attribute of an SCEP certificate
request.

Values can contain 0 to 32 ASCII characters (50
ASCII characters.

If the value contains $SERIALNO, it is replaced by
the phone's serial number. If the value contains
$MACADDR, it is replaced by the phone's MAC
address in hex.

Note:

• A password prompt is invoked when SCEP

is set for identity certificate enrollment and
the parameter value is empty.

• This parameter must not be set in a file that

is accessible on an enterprise network, and
only in a restricted staging configuration.

SDPCAPNEG

Specifies if SDP capability negotiation is enabled.

Table continues…

September 2017

Installing and Administering Avaya J129 IP Phone

121

Comments on this document? [email protected]

Summary of Contents for J129






































































































































Search results

Summary of Contents for J129

Reviews:

Related manuals for J129

Brands by name

Popular brands

Avaya J129, Installing And Administering

Search results

Summary of Contents for J129

Reviews:

Related manuals for J129

Brands by name

Popular brands