background image

Parameter name

Default value

Description

pattern configured in System Manager for Adhoc
Conferencing.

Depending on the dial plan, the dial string can
need a prefix code, such as a 9 to get an outside
line. The domain portion of the URI can be in the
form of an IP address or an FQDN.

The value can contain 0 to 255 characters. The
default value is null.

CONFERENCE_TYPE

1

Determines the selection of the Conference
Method.

Value Operation:

• 0: Local conferencing is supported based on

sipping services.

• 1: Server based conferencing is supported.

• 2: Click-to conference server based conferencing

is supported.

If the parameter is set to a value that is outside the
range then default value is selected.

Note:

The parameter is set to 0 in IP Office
environment.

CONFIG_SERVER_SECURE_M
ODE

1

Specifies whether HTTP or HTTPS is used to
access the configuration server.

Value Operation:

• 0: HTTP

• 1: HTTPS

• 2: Use HTTPS if SIP transport mode is TLS,

otherwise use HTTP.

This parameter is not supported in IP Office
environment as PPM is not supported.

CONNECTION_REUSE

1

Specifies whether the phone will use two UDP,
TCP, or TLS connection (for both outbound and
inbound) or one UDP, TCP, or TLS connection.

Value operation:

• 0: Disabled. The phone opens outbound

connection to the SIP Proxy and listening socket
for inbound connection from SIP proxy in parallel.

Table continues…

September 2017

Installing and Administering Avaya J129 IP Phone

91

Comments on this document? [email protected]

Summary of Contents for J129






































































































































Reviews: